Frigidaire Recent Questions, Troubleshooting Help & Support

If your Frigidaire Gallery side-by-side French door refrigerator model FGHF2366PFBA is not making ice after you switched the water filter, there are a few things you can check to troubleshoot the issue:

1. Check the water pressure: Make sure that the water supply to the refrigerator is turned on and that the water pressure is adequate.
2. Check the water filter: Make sure that the new water filter is installed correctly and that it is not clogged.
3. Check the water inlet valve: Make sure that the water inlet valve is not clogged or malfunctioning. It is located behind the refrigerator and controls the flow of water into the ice maker.
4. Check the ice maker arm: Make sure that the ice maker arm is not stuck in the off position.
5. Check the thermostat: Make sure that the thermostat is set to the correct temperature.
6. Check the control board: Make sure that the control board is not malfunctioning.

If the problem persists after checking these things, it may be best to contact a professional technician to diagnose and fix the issue.

It sounds like you may have an issue with the plug that connects the microwave portion of your Frigidaire PLEB27M9ECD built-in oven/microwave to the electrical supply. Here are a few things you can try:

1. Check the power supply: Make sure that the oven/microwave is properly plugged into a working outlet and that the circuit breaker is not tripped.
2. Inspect the plug: Look for any visible damage on the plug and make sure that the connections are secure.
3. Check the wiring: Make sure that the wiring inside the oven/microwave is not damaged or loose.
4. Test the outlet: Using a multimeter, test the outlet to see if it's providing power.
5. Test the microwave: If you have access to a known good microwave, you can test the plug by plugging it into the known good microwave and see if it works.

If none of these solutions work, it's likely that there is an issue with the electronic control board or the plug itself, which will require professional repair. It's best to contact the manufacturer or a professional technician for repair. They will be able to diagnose the issue more accurately and repair it.

It sounds like you may be experiencing issues with the heating element on your Frigidaire window AC/Heater combo unit. Here are a few things you can try to troubleshoot the problem:

1. Check the thermostat: Make sure that the thermostat is set to "Heat" and that the temperature is set to a level high enough to activate the heating element.
2. Check the air filter: A dirty air filter can restrict airflow and prevent the heating element from functioning properly. Clean or replace the air filter if necessary.
3. Check the heating element: The heating element may be faulty and needs to be replaced. Consult the manufacturer's manual or contact the manufacturer's customer service for further assistance.
4. Check the blower motor: The blower motor may be malfunctioning and needs to be replaced by a professional technician.
5. Check the wiring: Check the wiring and connections, ensure that all the wiring is securely connected and that there is no damage to the wires.
6. Check the fuses: Make sure that all the fuses are working properly and that they are not blown or tripped.

Keep in mind that attempting to repair an AC/Heater unit can be dangerous if you are not familiar with the proper procedures and safety precautions. It's best to let a professional technician handle the repair. If the problem persists, it's recommended to contact the manufacturer's customer service or a professional technician for further assistance. They can inspect the unit and determine the cause of the problem and provide a solution. Regenerate response

my best guess its A Frigidaire wall oven, circa 1966-1970,unsafe to use at any time if the temp controller trips the circuit breaker could be the oven thermostat causing the trip as well if Frigidaire are still in businessYou will need to ask an electrician to fit a /tested used controller or new superseded part temp controller and knob

Sorry about that useless reply from the new poster who seems to be guessing answers and probably thinks he gets paid for points. Everything on this site is voluntary. I checked and no one else has this problem that you have, which is unusual. My guess is that you have a fault with the door switch or more likely a bad connection on the display board. If can get to it, disconnect the connectors, spray them with electrical contact cleaner and reconnect. Another possibility is some type of feedback from the driver module on these new fangled LED Lights! https://www.google.com/search?q=Frigidaire+GRSC2352AF+panel+resets+when+freezer+door+opens ..

Hi, Please power cycle your dryer and attempt to run it again. If this fails, please ensure that your clothes are evenly distributed so that they weight of the clothes doesn't cause the dryer to be shutdown. Just to double check, please ensure that you've cleaned the lint track of your dryer. Lastly, you can use an power outlet extender to help switch the power outlet that you're using to run your dryer as there might be something wrong with your current one. Thank you.

There could be several issues that could cause your Frigidaire dryer to stop running after just a few seconds. Here are a few potential problems to consider:

1. Thermal fuse: The thermal fuse is a safety device that shuts off the dryer if it overheats. If the fuse has blown, the dryer will not run.
2. Clogged dryer vent: If the dryer vent is clogged, it can cause the dryer to overheat, which could trip the thermal fuse.
3. Faulty cycling thermostat: The cycling thermostat regulates the dryer's temperature. If it's faulty, the dryer may not run for more than a few seconds.
4. Faulty start switch: If the start switch is faulty, it could prevent the dryer from running.
5. Faulty door switch: The door switch prevents the dryer from running when the door is open. If the switch is faulty, the dryer may not run.

To fix the problem, you'll need to diagnose which of these issues is causing the problem and then replace the faulty part. I recommend having a mechanic diagnose and fix the problem for you.

According to the Frigidaire website, the cubic feet for the Frigidaire stand up freezer model MFU23BW4 is 23 cubic feet.

I had the same problem. I pressed the "Start Cancel" button, kept it down, then pressed "Rinse Only" button. The display then went clear. I pressed "Start Cancel" again, then "83" showed up on the display. I let it run its cycle, then it corrected itself. A little scary, but it worked. This answer board is great!

yes sounds like you missed the oven burners at the bottom of unit

You have to remove the rubber boot. It is very easy, just pull it off with your fingers. The spring is easy to strech most of the way around by hand, finish with a channel lock etc.

It sounds like there may be an issue with the water inlet valve or the wiring between the ice maker and the water inlet valve. Here are a few things you can try to troubleshoot the issue:

1. Check the water supply line: Make sure that the water supply line is properly connected and there are no kinks or blockages in the line.
2. Check the water inlet valve: Make sure that the water inlet valve is functioning properly and is not clogged or damaged. You can test the valve by jumping the two terminals with a small piece of wire. If the valve opens, it is functioning properly.
3. Check the wiring: Make sure that the wiring between the ice maker and the water inlet valve is securely connected and there are no loose or damaged wires.
4. Check the ice maker control board: The control board is responsible for controlling the ice maker and may be the cause of the issue if it is faulty. You can test the control board by unplugging the fridge and using a multimeter to check for continuity between the control board terminals.

If none of these troubleshooting steps resolve the issue, it may be necessary to consult the manufacturer or a professional appliance repair technician for further assistance.

Hi,

You can lay a fridge down if you do it right...this tip will tell you how to do it so that it will work again when you get it moved and set it back up.

Moving a Refrigerator What is the best way

heatman101

The E11 error code indicates a problem with the gas sensor DE32-60011A and or the wire harness DE39-40678D. Unfortunately the manufacturer has discontinued the sensor. You may want to try contacting local parts dealers, one of them might still have it in stock. Enter your part number in a search engine, a smaller company might have it or try eBay, Amazon or similar sites . Search by using the manufacturers part number. Try a used appliance store, sometimes they have the same model or a usable part for your machine.

Error Code ( E-23 )--------Clean the LID LOCK sensor,its almost located where you can see the LID LOCK came OUT and IN or Moving--which is functions to LOCK and UNLOCK the door cover ( Symptom ++ the LID LOCK will moving OUT and IN),open all the cover ,take out the LID LOCK sensor,open the LID LOCK sensor case until you can reach the COPPER connector which is act as the SWITCH .CLEAN the COPPER with paper sand or anything possible but not to damage the copper.After all put it back to the place intact.Hope it work,Mine worked with this procedure.+++++Toshiba AW-SD120S COST=== FREE OF Charge ( Do It Yourself )

Oven lock feature. https://www.google.com/search?q=Frigidaire+ples389ech+stovetop+cooking+display+is+showing+--+(two+dashes)+esec+lockout ..

a PAU is just saying the machine quit, unplug it from the wall for a minute and plug it back in, it may reset, let me know

F29 on all Frigidaire ranges means there is a communication error between the oven user interface and the touch panel. The control can't do the initial communication. This could be related to a wiring problem or a problem with the touch panel or the oven user interface board. Turn off the power to the range for 30 seconds to clear the code. If it returns, check that the wiring harness is fully seated. Check the wires for continuity and make sure that there is no corrosion on any of the pins. If the error repeats, replace the touch panel. If the error still persists, then replace the user interface board. Please add a comment with the model of the range for a parts list/diagram. I hope this helps. Cindy Wells

The compressor or other electrical components have quit working. Or there has been ice that has accumulated over the coils. Or the wiring is faulty or the plugs could be loose. The cord could be frayed.You will need to have the while model to be either repaired or replaced.

If you notice frost in the freezer that could indicate a burned out defrost heater. Might just be the smell. If you need further help, reach me via phone at https://www.6ya.com/expert/dan_73bbd84fe1d95b61