Kymco Logo

Kymco Recent Questions, Troubleshooting Help & Support

Do you work here? Claim your company

  • 414 Products
  • 5K Answers
  • 259K Views

Some scooters seat latches operate with the ignition key switch.
Turn it left and right as you lift the seat.
Sometime you have to push down on the seat while you turn the key
Some have a key right on the left side of the bike for the seat latch.

If you have no key, you can pull off the rear rack and then take off the plastics above the tail light.
Once that plastic is off you can reach the latch with a screwdriver or needle nose pliers.

Kymco Zing 125... | Answered on Oct 12, 2016


Hi, Tony for more information about your question and valuable "FREE" downloads that you will need please click on the links below. Good luck and have a nice day.
Kymco Stryker 125 150 Service Repair Manual Download Download Manuals... $10
Stryker II 125 DA25BB DA25BD Kymco Scooter Parts Racing Planet USA
KYMCO Stryker 125 User Manual FREE

Btw, I’m available to help over the phone in case u need at https://www.6ya.com/expert/gregg_c0ec1df182c7330e

Kymco... | Answered on Oct 11, 2016


Actually it looks interesting, however one reviewer said its not Chinese but Taiwanese. That is the part of China that has separated itself. As far as I am concerned the machine is still of a chinese extraction and seeing as many yamaha parts come from Taiwan. I shall have to dig deeper!

Kymco... | Answered on Oct 07, 2016


Hi, Pieter for this situation I would call my local dealer or reputable shop's service/parts department and inquire about any possible quick fix, answers, or parts inquiry. For more information about your issue and valuable "FREE" downloads that you will need please click on the links below. Good luck and have a nice day.
2007 Xciting 500 How to Recalibrate Speedometer
XCITING Speedometer Fail How to Solve
Motorcycle Message Board Motorcycle USA
Xciting 500 Service Manual ENG

Btw, I’m available to help over the phone in case u need at https://www.6ya.com/expert/gregg_c0ec1df182c7330e


Kymco... | Answered on Sep 25, 2016


A clicking starter solenoid is usually caused by a discharged or defective battery. I would charge the battery and check the connections. The battery voltage should remain above 10 volts WHILE CRANKING.

Kymco... | Answered on Sep 22, 2016


Hi, Anonymous I would love to help you with your engine or chassis noise but I just loaned my brand new pair of listening ears to your local dealer's chief technician so he could take your bike for a test ride and give you his professional opinion and estimate about your noise and repair cost. If you are a little short on "DRACHMA" and a Dealership is not on your list of fun places to visit then perhaps the list below will help soothe your worried mind so you can make an informed decision.
1. Bearings---SCREECH
2. Belts---HUM
3. Brake Rotors---BUZZ
4. Chains---RATTLE
5. Clutches---CHATTER
6. Shifting Trans---CLUNK
7. Front Forks---PLUNK
8. Rear Shocks---SQUEAK
9. Starters---CLICK
10. Solid Lifters---TICK
11. Hydraulic Lifters---TAP
12. Pistons---SLAP
13. Connecting Rods Go---KNOCK-KNOCK---who's there, it's me "*****"
For more information about your issue and valuable "FREE" downloads that you need please click on the links below. Good luck and have nice a day.
Top 6 Strange Motorcycle Noises What They May Mean
Noticeable Clicking sound
http://www.manualslib.com/manual/393386/Kymco-Agility-125.html
http://www.manualslib.com/manual/766732/Kymco-Agility-125.html#product-125 AGILITY CITY -

Btw, I’m available to help over the phone in case u need at https://www.6ya.com/expert/gregg_c0ec1df182c7330e

Kymco... | Answered on Sep 08, 2016


Hi, Phillip for this situation I would call my local dealer or reputable shop's service/parts department and inquire about any possible quick fix, answers, or parts inquiry. For more information about your issue and valuable "FREE" downloads that you will need please click on the links below. Good luck and have a nice day.
Motorcycle Electrical Ignition for KYMCO
Kymco Scooter Parts ATVs Scooter Parts Performance Scooter Parts...
http://www.kymcousa.com/owners/onroad/Xciting250-500_pre2008.pdf
https://absolutelyscooters.net/manuals/Kymco_Xciting_500_Service_Manual.pdf

Btw, I’m available to help over the phone in case u need at https://www.6ya.com/expert/gregg_c0ec1df182c7330e

2007 Kymco... | Answered on Sep 07, 2016


Hi, David for this situation I would call my local dealer or reputable shop's service/parts department and inquire about any possible quick fix, answers, or parts inquiry. For more information about your issue and valuable "FREE" downloads that you will need please click on the links below. Good luck and have a nice day.
Quality Replacement Parts For Kymco
Hipster 125 2V Hipster 125 4V RJ25AA RH25AA Kymco Scooter Parts Racing...
Genuine Kymco spare parts
KYMCO ZING 125 Manual

Btw, I’m available to help over the phone in case u need at https://www.6ya.com/expert/gregg_c0ec1df182c7330e

Kymco... | Answered on Sep 05, 2016


Hi, Geoffrey and the usual suspects are:
1. Severely discharged or a damaged battery, should have 12.5 volts or better and be able to pass a load test if necessary.
2. Failed alternator/generator and or voltage regulator.
3. Loose or corroded battery terminals and or cables especially the "NEGATIVE" cable, look for loose, corroded, or broken connectors inside the cable harness at "BOTH" ends.
4. Failed main circuit breaker or ignition switch, check for loose connections and continuity.
5. Failed system and or ignition relay, check for continuity.
6. Failed ignition coil, ignition/electronic module.
7. Failed CKP, CPS, CMP, MAP, TPS, or BAS sensor, corroded, loose or broken wire connector pins/sockets.
8. Throttle cables and or idle speed improperly adjusted hot idle speed should be 950 RPM to 1000 RPM.
9. Air/fuel mixture screw improperly adjusted.
10. Accelerator pump damaged or not working.
11. Water or dirt in the fuel system, carburetor or filter.
12. Restricted, blocked or kinked fuel line.
13. Fuel tank empty.
14. The gas cap is not venting properly or fuel tank venting system blocked.
15. A failed fuel pump, pressure regulator and or fuel injectors.
16. Vacuum line from intake manifold to petcock broken, cracked, or not attached, carburetor vent line plugged.
17. Needle and seat stuck closed in the float bowl.
For more information about your issue and valuable "FREE" downloads that you need please click on the links below. Good luck and have a nice day.
My scooter shut off while driving any ideas what it could be scooters
Scooter keeps cutting off while driving SCOOTER PROFESSOR
View topic Scooter just turned off while driving
http://www.scootermasters.com/manuals/People-250-Full-Manual.pdf
http://www.kymcousa.com/owners/onroad/Venox250.pdf

Btw, I’m available to help over the phone in case u need at https://www.6ya.com/expert/gregg_c0ec1df182c7330e

Kymco... | Answered on Aug 29, 2016


Hi, Christopher and the usual suspects are:
1. Idle circuit and transfer ports clogged.
2. Air fuel mixture adjustment too lean.
3. Pilot jet clogged.
4. Faulty accelerator pump.
5. Float level too low.
6. Float bowl contaminated old fuel, water, dirt, rust, etc.
7. Float bowl vent or overflow tube clogged.
8. Fuel flow to carburetor restricted.
9. Intake manifold leak.
10. The gas cap is not venting properly or fuel tank venting system blocked.
11. Vacuum line from intake manifold to petcock broken, cracked, or not attached, carburetor vent line plugged.
12. Needle and seat stuck closed in the float bowl.
For more information about your issue and valuable "FREE" downloads that you will need please click on the links below. Good luck and have nice a day.
http://www.scootermasters.com/manuals/kymco%20People%2050-complete.pdf
scooter dies if give it throttle
starts idles stalls giving gas Scooter Doc Forum
Bike idles perfect but dies when given the slightest amount of throttle 93...

Btw, I’m available to help over the phone in case u need at https://www.6ya.com/expert/gregg_c0ec1df182c7330e

Kymco... | Answered on Aug 27, 2016


Hi, Christopher and the usual suspects are:
1. Idle circuit and transfer ports clogged.
2. Air fuel mixture adjustment too lean.
3. Pilot jet clogged.
4. Faulty accelerator pump.
5. Float level too low.
6. Float bowl contaminated old fuel, water, dirt, rust, etc.
7. Float bowl vent or overflow tube clogged.
8. Fuel flow to carburetor restricted.
9. Intake manifold leak.
10. The gas cap is not venting properly or fuel tank venting system blocked.
11. Vacuum line from intake manifold to petcock broken, cracked, or not attached, carburetor vent line plugged.
12. Needle and seat stuck closed in the float bowl.
For more information about your issue and valuable "FREE" downloads that you will need please click on the links below. Good luck and have nice a day.
Bike idles perfect but dies when given the slightest amount of throttle 93...
starts idles stalls giving gas Scooter Doc Forum
scooter dies if give it throttle
http://www.scootermasters.com/manuals/kymco%20People%2050-complete.pdf

Btw, I’m available to help over the phone in case u need at https://www.6ya.com/expert/gregg_c0ec1df182c7330e

Kymco... | Answered on Aug 27, 2016


Hi tighten the axle nuts ...if this does not help loosen axle nuts jack it up tighten nuts & when on the ground tighten them again, cheers

Kymco Maxi XL... | Answered on Aug 27, 2016


Hi, Cutty you have more issues than just the key your entire fuel system has turned to varnish for this situation I would call my local dealer or reputable shop's service/parts department and inquire about any possible quick fix, answers, or parts inquiry. If necessary, transport your bike to the dealer or shop and have a professional technician take it for a test drive, if it is in running condition, and give you a written estimate of repairs and answer any specific questions you may have about your problem. For more information about your issue and valuable "FREE" downloads that you will need please click on the links below. Good luck and have a nice day.
KYMCO AGILITY 125 Service Manual
Kymco Scooter Parts ATVs Scooter Parts Performance Scooter Parts...
http://www.manualslib.com/manual/766732/Kymco-Agility-125.html#product-125 AGILITY CITY - (copy&paste)

Btw, I’m available to help over the phone in case u need at https://www.6ya.com/expert/gregg_c0ec1df182c7330e

Kymco... | Answered on Aug 15, 2016


Hi, Ian sounds like you may have a faulty electrical connection somewhere in the ignition circuit and the usual suspects are:
1. Ignition Switch not in the "ON" position.
2. Engine Run Switch in the "OFF" position.
3. Discharged battery, needs to be 12.5 volts or better and be able to pass a load test if necessary.
4. Check the battery terminals for damage or corrosion check the battery cables at "BOTH" ends for loose, corroded, or broken connectors, "INSIDE" and outside the cable harness, perform connector wiggle test and check cables with an ohmmeter if necessary.
5. Bank angle sensor tripped and ignition/light key switch not cycled to the "OFF" position and then back to the "ON" position.
6. Faulty ignition switch.
7. Faulty starter button.
8. Faulty kickstand or clutch pull in switch/sensor.
9. Security alarm needs a reset.
10. Starter control circuit, relay, or solenoid faulty.
11. Main fuse or circuit breaker may be blown or faulty.
12. Electric starter shaft pinion gear is not engaging or over-running starter clutch slipping.
For more information about your issue and valuable "FREE" downloads that you will need please click on the links below. Good luck and have nice a day.
http://www.kymcousa.com/owners/onroad/Quannon150.pdf
http://www.enmoto.com/enmotoonline/downloads/Specifications/Kymco/Schaltplaene/Quannon.pdf

Btw, I’m available to help over the phone in case u need at https://www.6ya.com/expert/gregg_c0ec1df182c7330e

Kymco... | Answered on Aug 05, 2016


Hi, Sonia excellent question it all depends on how long you have owned the scooter and it's mileage, engine oil needs to be changed every 2000 km or 1250 mi. gear oil needs to be changed every 4000 km or 2500 mi.I recommend 10w40 in a synthetic "motorcycle" (not automobile) engine oil if you can find it, Amsoil and Mobil1 are the best and for the rear differential, SAE 80w90 gear lube is recommended, for this scenario you will need your service/owners manual if you can't find the first and best tool you ever bought for your Kymco, despair not, for a mere $0 you can download another one. For more information about your issue and valuable "FREE" downloads that you will need please click on the links below. Good luck and have a nice day.
Kymco People 150 Espresso oil filter change
Gear Oil change on 2013 Kymco Super8 150
http://www.kymcousa.com/owners/onroad/People50-150.pdf

Btw, I’m available to help over the phone in case u need at https://www.6ya.com/expert/gregg_c0ec1df182c7330e



Kymco... | Answered on Aug 04, 2016


Hi, Geoffrey for this situation I would call my local dealer or reputable shop's service/parts department and inquire about any possible quick fix, answers, or parts inquiry. Good luck and have a nice day.

Btw, I’m available to help over the phone in case u need at https://www.6ya.com/expert/gregg_c0ec1df182c7330e

Kymco... | Answered on Aug 02, 2016


Hi, Anonymous for this scenario you will need your service/owners manual if you can't find the first and best tool you ever bought for your Kymco, despair not, for a mere $0 you can download another one. For more information about your issue and valuable "FREE" downloads that you will need please click on the links below. Good luck and have a nice day.
how to set and adjust the cam and cam chain timing 4 stroke engines ATV...
How To Set Cam Timing
Valve Cam Timing
KYMCO ZING 125 Manual

Btw, I’m available to help over the phone in case u need at https://www.6ya.com/expert/gregg_c0ec1df182c7330e



Kymco... | Answered on Aug 02, 2016


a dead short probably . use a multimeter or an OHMmeter and check it out .

Kymco... | Answered on Jul 30, 2016


anything that has a plastic fuel tank in it is a common problem 4 leaks !! I've had brand new chainsaws , tractors, and yep even bikes come in here with fuel drips !! its them plastic fuel tanks everytime !! they jjust cant take the chassis flex the ole metal ones could (but then again ive never seen plastic rustout either ) and they get small cracks in them right where they attach to frame most times too !!

Kymco... | Answered on Jul 29, 2016


Hi, Eric your engine is liquid cooled you may have blown the head gasket and should take it to a dealer for repair for more information about your question and valuable "FREE" downloads that you will need please click on the links below. Good luck and have a nice day.
http://www.49ccscoot.com/manuals/Kymco_Super9_SH10DA_Service_Manual.pdf
Super 9 LC 50 Kymco Scooter Parts Racing Planet USA
http://www.scooterunderground.com/knowledge/manuals/pdf/Super%209%20Owner's%20Manual.pdf
Kymco Super 9 LC 2005

Btw, I’m available to help over the phone in case u need at https://www.6ya.com/expert/gregg_c0ec1df182c7330e

Kymco... | Answered on Jul 27, 2016

Not finding what you are looking for?

Ask a Question

Usually answered in minutes!

Top Kymco Experts

Marvin
Marvin

Level 3 Expert

84540 Answers

Kardoc

Level 3 Expert

4424 Answers

Andrew Taylor
Andrew Taylor

Level 3 Expert

26381 Answers

Are you a Kymco Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...