Kymco Logo

Kymco Recent Questions, Troubleshooting Help & Support

Do you work here? Claim your company

  • 414 Products
  • 5K Answers
  • 258K Views

Hello !
Being an automatic shock, you can not manually interfere with it.
If the shock is not working in the cold season, fault is the lack of power supply, or internal shock failure, more likely the thermistor pocket, creates problems by shortening it in most cases, or the connections of the slipper connectors etc.
Check the presence of alternating voltage (12 volts) of power supply after starting the engine, with a small 12-volt bulb, or with a measuring device.
With the engine off, disconnect the connectors, and with the Rx measuring instrument, also measure the thermal resistance of the thermistor, and the state of the contacts, you should find approximate 40-60 Ohms.
Any deviation higher upwards or downwards, indicates a malfunction, and must be interfered with when it is removed.
The construction shoe consists of a metallic capsule of the size of a cigarette filter, which at one end has a rod that comes in or out of the environment. At the other end is the thermistor, which is powered by a 2-wire the scooter's engine.
This voltage heats the thermistor, which in turn heats the thermostatic capsule, it has an inertia to the piston's expansion, dictates the time for the heating of the engine, etc.
at maximum cascade heating, rod relaxation will act and reduce excess gasoline, the engine entering normal speed.
Hopefully, I was very helpful!
Good luck

2005 Kymco Zing... | Answered on Mar 13, 2019


You've got a Ignition System Issue which narrows things down quite a bit. It's either the ignition switch that your key goes into, or an on/off(run/stop) switch, or it's a relay for the ignition systems(or starter relay), if it's none of those then it's the starter solenoid that you've been jumping with the screwdriver, it sounds like the starter is working as it should since it turns over- the reason it turns over but won't actually run is because the ignition system won't work unless the key is inserted and in the run position, or if there's any other on/off switch that controls your engine it could be there. I'm not familiar with this exact bike but this is a common issue with all motorized machines! You can bypass all of this but that requires running some wires and a couple of switches plus a relay or two- that's an option but don't do that as your issue is nothing major and would be easier to fix than to go through the trouble of re-wiring it all. Just start troubleshooting and eliminate one part at a time, check relays, fuses, and electrical connections first, then the individual components I listed above and check to make sure they have power coming in and out when/where they're supposed to. If your bike turns over but won't run and the key is on, and you have a functional Ignition system then you need to verify you have ignition by checking your coil's output. EASIEST way to do so is pull a spark plug and connect it to the spark plug wire as you normally would, then hold the spark plug against the engine to ground it and turn it over- you'll see if you have any spark jumping aroundbetween the spark plug's electrode and the base of the plug itself. Either way, you'll get this figured out now that you know where to start and what to check!


76522e9f-b2bb-4336-a115-e53197ce5a3b-pujhmq5yz2fla13a1caeolco-4-0.jpeg

Kymco... | Answered on Feb 27, 2019


choke it ? gas not getting to piston air filter clogged ?

Kymco 2015 MXU... | Answered on Feb 21, 2019


belt drive ? or chain. ? belt slipping ? sprocket on chain loose?

Kymco 2011 UXV... | Answered on Feb 21, 2019


Check all wiring connections and especially those on the battery, starter, and starter solenoid(if seperare from battery). It sounds like something is just making a bad connection since it won't even turn over- I bet your problem is in this area, good Luck and if I've been helpful please click the green button to let me know, Habe A Great Day!

Kymco... | Answered on Jan 26, 2019


Can be a loose / bad connection somewhere in the high current starter circuit, or a flat battery.
Did it start ok a few times when you put in the new battery?
Yes >> not charging the battery (or not charged when fitted).
No >> Bad connection between battery and frame or between battery and main ignition key power connection point (usually to a fuse).
The cause of solenoid clicking is the voltage dropping dramatically when the starter current begins to flow, usually a flat battery or a loose or dirty connection in the starter current circuit (will generate heat when clicking which can help you find it).

Kymco... | Answered on Jan 20, 2019


Your first option is to check the basics.
Is there fuel in the tank? Yes, I know that sounds silly but I have done it!
Check that the fuel lines all the way from the tank aren't blocked.
Is there a fuel tap, (petcock), fitted? They usually have a gauze filter built into them that might need cleaning.
Is the fuel filter a new one?
When was the last time the carb was overhauled?

Kymco... | Answered on Jan 11, 2019


, usually due to a leaking fuel line or malfunctioning fuel injectors. However, it is normal for a small amount of gas to get into the engine oil during normal engine operation.

Kymco 2011 UXV... | Answered on Jan 04, 2019

Not finding what you are looking for?

Ask a Question

Usually answered in minutes!

Top Kymco Experts

Marvin
Marvin

Level 3 Expert

84027 Answers

Andrew Taylor
Andrew Taylor

Level 3 Expert

25819 Answers

Steve P
Steve P

Level 3 Expert

3530 Answers

Are you a Kymco Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...