Hitachi Popular Questions, Answers, Tips & Manuals

Hello, open flap, press and hold down button A whilst depressing the small reset button B using a pointed instrument.

What is the TV source or input? Unless the source is antenna or cable using the antenna in, the captions have to be disabled at the set-top box that is providing the signal. Some set-top boxes have a CC button on the remote but many have this hidden in the menu system. My IPTV box requires me to press Menu, choose the Settings menu and then enter a code provided by the provider. Once in the menu, the captions are enabled in the Hardware > Audio menu. Some satellite dish set top boxes have different access methods depending on the TV setup. If you have a master box that feeds two TVs, the setting menu to control the closed captions was only available on the TV closest to that box. (This was the case for a Dish receiver with a Single or Dual mode. In single mode, turning on the CC enabled the captions for both TVs. In dual mode, the two TVs could be tuned to different channels but only the TV nearest the set top box would display the closed captions if the feature was enabled. On that receiver, the closed captions were reached by pressing Menu. Then the captions options were under Properties > Closed Captions.) Please indicate what the TV source is for further information on where the sub-menu for the closed captions will be toggled on and off. I hope this helps. Cindy Wells

The projector has a RGB input So to use it on a VGA output from the computer you would need a VGA to RGB adapter or something like this adapter https://www.auselectronicsdirect.com.au/hdmi-to-vga-and-rgb-component-converter with a component cable as projector has component inputs also

If available for your OS they will be on the Hitachi web site.

charger failure

My Smart TV has that problem too , open it and repair led of LCD

It is part 112 on the parts schematic but gives no indication https://www.ereplacementparts.com/hitachi-c10fcb-compound-miter-saw-parts-c-7927_13297_13413.html Manual doesn't show either https://www.hikoki-powertools.com/manual_view_export/pdf/H99322813_C10FCB_405.pdf Aha, a Service and Repair Manual. Perhaps that will help? https://www.manualslib.com/manual/799928/Hitachi-C-10fch.html#page=23-manual ..

It is the Indoor Printed Circuit Board. https://www.google.com/search?q=Hitachi+inverter+AC+indoor+light+3+time+blinking+error ..

Your charger has failed.

buy a remote or fix the button

either the switch is bad or the motor brushes worn out

replace the switch of course

Try resetting the power by switching off the TV and then switch off the TV's power outlet and disconnect the TV's power cable from the outlet. Press and hold the TV's Power button for about 30 seconds to drain any residual power from the TV and then release the button. Turn on the TV in the normal manner and see if it turns on then afterwards.

probably a back light issue

If you wish to get some details; check the site linked here. Pull up older posts. https://electronicshelponline.blogspot.com/ https://elektrotricks.blogspot.com/ faults & possible causes to LCD & Plasma screen are given with illustrations. You can get an idea about the fault to an extent. Search the site by type in the brand name of your set, in its search bar at the right side column, and press enter.

Replacement screen is required, so a new tv is probably cheaper.

Bad fuel is the #1 reason for this - check the expiration date on the bottom of the fuel cell. Some stores don't rotate their stock, so it doesn't matter if you just bought it. If you're sure the fuel is good, I would check the cycle - 1) Disassemble the tool, plug the battery in, without depressing the nose, just pull the trigger (Fan should start) If the fan doesn't start, it will either be the trigger or possibly the fan motor. 2) With your hands in a safe location away from the fan blade, depress the head switch (Fan should start & light should be steady green), then pull the trigger - you should have a nice sharp, blue spark. If step 1 is OK and step 2 produces no spark, it will most likely be the ESU

LEARN TO USE THE SPELL CHECK FEATURE ON YOUR DEVICE . THERE IS NO SUCH THING AS A TRIGGER VALUE

Could be backlights blown or T-con board faulty, test both.

Nope. hi8 was newer technology. hi8 camcorder could play older 8mm videos but not vice-versa. hi8 video has higher resolution then older 8mm