Dremel Tools & Hardware - Others - Recent Questions, Troubleshooting & Support


This is the charger, its getting a reading from the battery that its charged when it isn't. I don't know exactly how that charger is wired but, to be suroe it is the charger, as I have had similar problems beforehand.

Dremel & Stylus... | Answered 3 days ago


It's possible that the enameled copper coiling on the stator was compromised when it overheated creating a short. Sadly, unless you have a replacement stator is cannot be fixed. Sorry.

Dremel Tools &... | Answered on Feb 11, 2019


Please help. Because l am in Australia l can't phone the tecnition and the link to get the manual doesn't go any where, neither does the dremel website, nothing happens, and every time l try to do something in this site l get catapulted back to the begining of the page. Frustrating! Can someone help me with the manual?

Dremel & Stylus... | Answered on Dec 30, 2018


Change the capacitor 220uF and it will most certainly work again. I got the idea from FixYa and it solved my problem!
Easy to change just 2 soldering points and a component costing around 0,2 Euros. If you do not know how to operate a soldering tool ask someone for a quick assistance. The switch takes around 2 min (1,5 min to open the charger and 0,5 min to change the component!).

/Johan

Dremel & Stylus... | Answered on Dec 30, 2018


3 in 1 is a light oil used the lubricate small joints, plates and bearings. It can also be used as a releasing oil for stuck bolt etc. 3 in 1 is usually ok to use in small amounts to grease the bearing points on your Dremel.

Dremel Tools &... | Answered on Dec 23, 2018


The battery has been overcharged.
You will need a new one.

Thanks!!!!

Dremel 10.8-volt... | Answered on Dec 11, 2018


You can use canned air for light dirt,or compressor with blow gun for heavier dirt.

Dremel Tools &... | Answered on Nov 04, 2018


I don't know if it has a fuse - I know little about the Dremel brand but I have had some experience of similar other brand tools. The electronics seem less than completely reliable being physically too small for the job of speed regulation, torque compensation, radio interference suppression, etc. - everything is crammed into a tiny space and the circuit board is typically on the cheap and nasty side. If there is a fuse it would typically be found on the circuit board.

Mostly the failure of such tools, in my experience, is caused by the electronics though nothing can be ruled out.

I suggest you check the mains cord using a multimeter and then check the motor and if both are OK it is fairly safe to assume the fault is circuit board related.

Dremel Tools &... | Answered on Oct 27, 2018


You can call Dremel direct at 1-800-437-3635 and order the part. Let me know if you need more information.

Dremel 395... | Answered on Oct 25, 2018


Takes an adapter to screw onto the nose of the Dremel. The shaft itself is gripped by the correct size collet tightened as you would any bit.

Dremel 225... | Answered on Oct 25, 2018


Look at eReplacementParts.com and the parts diagrams,

If you need more help come back.Post / thumbs / testimonial are welcome!

Dremel Variable... | Answered on Oct 25, 2018


find the little square attachment and place on the end of the dremel tool. I didid the same thing. Worked fine after I put the other part on.

Dremel Variable... | Answered on Oct 25, 2018


It doesn't attach anywhere, that's why it popped out. It should just fit in a recess, pushing the lock button outward.

Dremel Variable... | Answered on Oct 25, 2018


the collet is either the wrong size for the shaft on the attachment or is missing alltogether

Dremel Variable... | Answered on Oct 25, 2018


No.. the issue issue is the switch inside. when your Dremel 4200 stop working, press firmly the grey area between the speed selector and the brush housing. I think this a defect in the design of the 4200. 9f840401-fb84-4f7b-8c68-75a9be3ceb9e.jpg

dremel-4200-stopped-working-sc23h3bxyncdov434g0b1kv3-5-2_0.jpg

Dremel Tools &... | Answered on Oct 08, 2018


The flashing light indicates an error, possibly your battery is shot or malfunctioning. New battery needed.

Dremel Tools &... | Answered on Oct 02, 2018

Not finding what you are looking for?
Dremel Logo

597 questions posted

Ask a Question

Usually answered in minutes!

Top Dremel Tools & Hardware - Others Experts

cluffermon

Level 1 Expert

3 Answers

Mike

Level 3 Expert

4356 Answers

Sheldon Dedek

Level 3 Expert

909 Answers

Are you a Dremel Tool and Hardware - Other Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...