Dremel Tools & Hardware - Others - Page 2 - Recent Questions, Troubleshooting & Support

Well, yes you can measure the switch, look for continuity. I suspect something else is wrong, some models had armature issues. Measure the coils and armature for continuity.

https://www.eternaltools.com/blog/complete-guide-to-your-dremel-rotary-tool https://www.eternaltools.com/felt-polishers https://us.dremel.com/en_US/products/-/show-product/tools/684-01-cleaning-polishing-accessory-set

The flashing light indicates an error, possibly your battery is shot or malfunctioning. New battery needed.

More supports, please refer to www.dieselgeneratortech.com

There might be many reasons but the one of them is you might be obstructing its air intake passage and it is over-heating.

You can call Dremel direct at 1-800-437-3635 and order the part. Let me know if you need more information.

If the threads on the nut or shaft are stripped, the nut will turn freely and it can be removed with pliers by turning and pulling at the same time. If it won't turn, it is probably galled or cross-threaded. In that case, try penetrating oil first. If that doesn't loosen it, try heating the nut with a butane or mapp gas torch. Good luck.

your best bet will be ebay Then if that's not successful, check with these people https://www.ereplacementparts.com/search_result.php?q=Charger%2C+dremel+1100 You'll need to know the voltage. The 100 volt charger is discontinued. They carry authentic Dremel parts.

https://all-guidesbox.com/model/dremel/850.html https://www.dremel.com/en_US/support/manuals https://www.dremel.com/en_US/support/manuals/other-tools

You screw off the collar on the tool, remove the chuck and inner part. The chuck is replaced with a special chuck (no inner piece). The special chuck has a square opening in it's nose that accepts the square end of the flex shaft inner cable. Is is actually a speedometer drive cable, from yesteryear. Then you pull the inner cable out slightly, if it will, and put the inner cable into the square opening of the special chuck on your dremel motor. once engauged, you carefully screw the outer shaft housing on to the end of your dremel motor. What you want to avoid is damaging this area during flex shaft assembly. I have had success with turning the output side of the flex shaft, while tightening the outer flex shaft onto the dremel motor. Stop tightening if it starts binding... Rotation seems to help with alignment of all parts. Cheers, Doc

spray lube or oil and use pliers to move it back and forth

Just some observations: - The correct blade has ti be installed. - It has to be sharp - It can only cut material intended for that blade.

Change the capacitor 220uF and it will most certainly work again. I got the idea from FixYa and it solved my problem!Easy to change just 2 soldering points and a component costing around 0,2 Euros. If you do not know how to operate a soldering tool ask someone for a quick assistance. The switch takes around 2 min (1,5 min to open the charger and 0,5 min to change the component!)./Johan

Black is positive(+) and white negative(-).
Circuit board should be marked.

It's possible that the enameled copper coiling on the stator was compromised when it overheated creating a short. Sadly, unless you have a replacement stator is cannot be fixed. Sorry.

Please help. Because l am in Australia l can't phone the tecnition and the link to get the manual doesn't go any where, neither does the dremel website, nothing happens, and every time l try to do something in this site l get catapulted back to the begining of the page. Frustrating! Can someone help me with the manual?

3 in 1 is a light oil used the lubricate small joints, plates and bearings. It can also be used as a releasing oil for stuck bolt etc. 3 in 1 is usually ok to use in small amounts to grease the bearing points on your Dremel.

The battery has been overcharged.
You will need a new one.

Thanks!!!!

You can use canned air for light dirt,or compressor with blow gun for heavier dirt.