Canon imageCLASS - Recent Questions, Troubleshooting & Support

Question edited for clarity, full make model, and turned around. Question moved to Canon ImageCLASS category. If it actually feeding the paper and printing blank pages, it is very unusual. That should be impossible. https://www.google.com/search?q=canon+ir+advance+c5235+blank+paper ..

Hi
Error 6A00
The 6A00 is a Canon generic code for paper path jam.

Solution 1:
Move the printhead carriage back and forth a few times.

Solution 2:
Check the purge unit: Moving the print head assembly will not clear a purge unit if its jammed with paper, paper clips, push pins, screws, cookie crisp, flower bud pods or the like.

Solution 3:
Press the ink pads down in the purge unit.
Please come back and just gave a vote, it will gave me some satisfaction to know am helping some one so I will keep on helping.
All The Best: Pineworks

This problem bugged me for months! Selecting CONT. PRINTING as indicated by Small6363 allowed to print with the warning light on but did not solve the warning light problem. I eventually found a way to bypass the flashing light and warning message.

Underneath the cartridge, on the cylindrical portion, in the middle there is a small flat rectangle. This is the ink level detection spot. Cut a piece of aluminum foil of the same size and place it with a piece of scotch tape overt that flat rectangle. Voilà! No more flashing red light and no more out of toner message! Of course you have to monitor your level visually and change the cartridge when printing starts to fade.

Hope this helps!

Patrick

Support ' Support Laser Printers - imageCLASS ... - Canon

https://www.usa.canon.com/.../printers/...laser-printers-imagec...

Canon Inc.The imageCLASS MF8380Cdw delivers fast and accurate printing in approximately 14.3 seconds with Canon's Quick First Print Technology. Multi-page ...Missing: mf4150 ‎panel ‎remain ‎response

Amazon.com: Customer Questions & Answers

www.amazon.com/ask/questions/asin/B000J4J70Q

Amazon.com, Inc.Canon imageCLASS MF4150 Laser Duplex P/s/c/f 21PPM Adf ... make a two side

http://www.xerox.com/about-xerox/contact-us/enin.html

• Contact Us - Xerox Find a local Office Products dealer in your area: Kolkotta Office Xerox India Limited 37, Shakespeare Sarani, 1st Floor, Kolkata - 700 071. Sales: 033 - 44004875 ... http://www.xerox.com/about-xerox/contact-us/enin.html
• Copiers like the Xerox personal copiers offer functionality that takes into consideration ... 8/1, Lalbazar Street, Room No.1 D ,1st Floor, Kolkata - 700 001, India. http://www.copier.in/photocopiers/personal-copiers.html

Canon ir 6000 error e225 is a ccd, lamp rcon pcb replace

Question edited for maker and to make a proper question. Question moved from Television and Video category. All question need FULL 'make model (what it is)'. ImageCLASS covers about 40 models of different sizes and features. The most likely reasons are; White Out in the document feeder scan strip. Torn paper somewhere in the paper path. A bad developer roller.

Question edited for clarity. Question move from Canon computers to imageClass Printers. Yes, disconnect from the power overnight. Support contact number here https://www.usa.canon.com/internet/portal/us/home/support/details/printers/black-and-white-laser/mf217w/imageclass-mf217w ..

1. Open the printer driver setup window.
2. Select the paper size. Select Custom... for Page Size on the Page Setup tab. ...
3. Set the custom paper size. Specify Units, and enter the Width and Height of the paper to be used. ....set discord custom in private
4. Complete the setup.

No it's not. Make sure to open EVERY door on the printer and check for any additional paper. Also, power the printer off and back on a few times and see if it goes away.

Dear Inside the back panel there are paper sensors attached to lever, a small spring connected to lever to keep its home position, the spring may dislocated from its position or the lever sticked to the base. some times a small piece of paper sticked at this may cause the problem. Thanks.

I have just had the same problem on one of these Canon MF4150 machines.
The manufactures warranty on our machine had expired just one week before this happened so I had to fix this myself.
The problem we had (which is very likely to be the same cause as yours) is when we removed some torn jammed paper, it had somehow pulled off a spring from inside the machine. The spring was linked to the paper jam sensor.
It does involve a LOT of work to fix it, and unless you are very 'techy' it may be quite a difficult task to do this for the 'average' person.
I had to completely disassemble the machine: Take off the front first (lift up the cover and there is 2 screws at the front and 2 clips on the bottom of the machine) Then remove the 2sides and finally the top (screws should be easy to see, to get the sides off, un-clip along the front edges and gently move them outwards and slide them backwards to release the clips on the back) being careful with the wires going to the scanner part). Then look for the fuser unit which is near the top at the back, there is a black rounded cover over the fuser. To remove the cover, look for 2 small clips one at each side and unclip the cover and gently lift upwards.  Under the cover on the left side you will see a small plastic rod which goes from the left side to a small tab in the middle, if you look about half way along that rod you should see a tiny spring, make sure this is clipped on properly and that you are able to rotate the rod and it should spring back to the proper position when you let go.
Once this is done, put it all back together again and it should work fine.

I'm sure a lot of other people probably have this same problem too so I hope this helps someone.

Remove toner cartridge. You will find paper piece in there, I believe. Get ALL pieces out, put in fresh paper, restart. That usually does it.

first of all, download updated driver from software.canon-europe.com and install ( before install, remove old drivers and programs) and if appears again, change your network cable.

Canon, Brother, and Epson's Printer solutions are mostly the same check this answer. The Brother Printer offline Windows 10 error normally shows up because of various mechanical issues. There can be difficulties with attachment, print queue, or something else. The printer may be facing some other error. Commonly, the Brother printer will stop printing when Brother printer offline error occurs. 10 steps that Fix Brother Printer Offline Windows 10:- 1. Make Sure The Printer Is Properly Connected. 2. Verify Printer Is Not In Sleep. 3. Check Brother Printer For Any General Errors On Computer. 4. Check Printer Status Offline Or Paused. 5. Check For Copy Of Printer In Devices And Printers. 6.Long Print Queues On Computer. 7. Make The Brother Printer Default. 8. Check SNMP Status. 9. Update Brother Printer Drivers. 10. Update Windows 10 OS. FULL SOLUTION- Brother Printer Offline Windows 10 If you are not a Technical guy you can take help with us. by just call in Toll-Free Number that is given on Mentioned Blog.

I had the same cr@p of the problem yesterday. The problem was not in the paper. You have to do 2 simple things, from which one will solve the problem.
first, download the latest drivers and install them.
And the more important thing, the problem occurred due to incorrect paper format. Solution is very simple. Open MS word or something similar, file->print.. and before you print open Properties menu. There for the Output Size will be selected "Match Page Size". you don't want that (i don't know why it doesn't work), but the solution is manually select A4, or whatever your page size is.

hi. that error indicates the laser unit is malfunctioning. maybe is dirty or damaged

Your Printer system software having problem, upgrade system software. please contact canon technician of your area. your own you cannot update that mechine.

My MF 6530 printer began printing light so we changed the cartridge and the machine began printing blank pages. When the other cartridge was put back in the machine, it too began printing blank pages. We have several of these machines in a couple of offices and have had this problem before. Canon is aware of the issue with this model, but I would like to know it as well. Can you help with what the problem is and the repair instruction? A friend of mine with this machine and the same problem, had called Canon and they had repaired it quite fast in his office. I'd like to do it myself in case it re-occurrs.