20 Most Recent
Sta Rite Sta-Rite Max-E-Therm High Effiency - Propane Heater - 333,000 BTU - Page 4 Questions & Answers
Sta Rite Pool Heater is
Hello.
Tech. man you can only make use of jumper for some few time just because the jumper will not have any form of court out whenever the pressure is high to regulate the power supply .
Moreover, when ever a fuse need to replace with an other it most not be twice the old capacity you can make use of the range of 1.50A OR 1.75A OR 2. PLEASE DOT MAKE USE OF 2-3A WHILE because it will be too high for the power regulation .
Think of safety first.
Thanks.
10/7/2011 6:15:59 AM •
Sta Rite...
•
Answered
on Oct 07, 2011
Our spa heater has no
If one of my customers had this issue with their heater I would call the Sta Rite technical support at 888-782-7483 and they would likely be able to help you diagnose this issue.
Please let me know how this works out and ask subsequent questions. Thank you.
9/4/2011 12:29:45 AM •
Sta Rite...
•
Answered
on Sep 04, 2011
Re error code E05 on the max e therm---what are
Hi 1933tudor,
An E05 error codes are associated with heater control board or the gas supply. You can find the information about this error in this PDF file of the owner's manual. The repair can often be challenging.
Hope it helps.
Thank you for using FixYa.
7/19/2011 2:47:36 AM •
Sta Rite...
•
Answered
on Jul 19, 2011
Starts up and flares out.I
Hello,
Please can you rephrase the question in a way i would be able to
understand it and assist you. I would be very glad to be of help to you.
You can post a comment with the full question then i will be able to reply you with solutions to the question on ground.
Would be hoping to read from you on the problem so as to provide a solution for you.
Elect_Comp
6/29/2011 9:43:33 PM •
Sta Rite...
•
Answered
on Jun 29, 2011
Heater will not fire. On
Look on the wiring diagram inside the access panel or near the access panel. There should be notes on the bottom of the diagram telling you what the error codes mean (error codes are your flashing yellow lights).
Let me know if the description on the wiring diagram is not obvious.
-Mark
6/7/2011 7:22:31 AM •
Sta Rite...
•
Answered
on Jun 07, 2011
I purchased a max e therm 200HD natural gas heater
It sounds like an incorrect gas/oxygen mix. When installing a new heater, one of the most important things to due is to check the manual for minimum acceptable gas line and pressure. If you gas pressure is too much, or too little, you can burn a brand new heater to the ground really quick.
Not only is it important to have the correct gas pressure, but the piping size for available gas is very important too.
Id say with the issues you are having, start from scratch. Goto your manual and make sure the minimum gas line has been installed. Then if you are going to do this yourself, you need to purchase a monometer to dial in the gas valve on the heater. Without a monometer you should not be installing any gas appliance. All minimum and maximum requirements will be in the manual.
1/24/2011 5:05:28 PM •
Sta Rite...
•
Answered
on Jan 24, 2011
When I start up my
Hi,
Error pertains to stack flue sensor setting.
There are two modes for low level programming and default is a (0) Zero but for outdoor spas this must be reset to a one ( 1 )
Just hold the off button down for 30 seconds let up, press down again, use arrow buttons on key pad to set from 0 to 1.press off again.
post a comment for further assistance.
Thank you for using fixya have a nice day:-)
1/21/2011 5:02:51 PM •
Sta Rite...
•
Answered
on Jan 21, 2011
I have a starite propane heater i turn it on it
This is either one of two thing.
Either you pump is clogged, or failing and not providing adequate flow, or the heat exchanger has a hole in it. I would hope that it is just a flow issue as the exchangers are very expensive.
Check the pump first, and also make sure there is no leaking water from the heater
11/15/2010 11:19:04 PM •
Sta Rite...
•
Answered
on Nov 15, 2010
Heater gives code E05
This code if for ignition failure. Your glow plug has probably gone bad and will need to be replaced.
9/9/2010 3:54:24 AM •
Sta Rite...
•
Answered
on Sep 09, 2010
I have a sta rite heater installed about a year
If this is a propane heater and you have changed the meter that means you have natural gas. A converstion kit is avable and all it is is a washer in the gas line inside the heater. You can buy these but my wholsaler just gives them to me when I get a heater. Get your installer to do this for you first before you buy anything else. Also check the size of your gas pipe to the unit. It need's to be sized to the heater and the run of pipe. You can find this info in your book that came with the heater.
9/8/2010 8:21:14 AM •
Sta Rite...
•
Answered
on Sep 08, 2010
I have two error codes:
Error pertains to stack flue sensor setting.
There are two modes for low level programming and default is a (0) Zero but for outdoor spas this must be reset to a one ( 1 )
Just hold the off button down for 30 seconds let up, press down again, use arrow buttons on key pad to set from 0 to 1...press off again....play with it and see for yourself...I don't now why Sta-rite buries this information and makes us guess.
Again, on mine, this all pertains to the Stack Flue Sensor setting.... you can look at your heater and see what they look like...outside toward bottom the SF must be a 1 and not Zero or you get the quick flash 128-R8 notice...also, the Stack flue senor is finicky and connections must be good...use steal wool to re-seat but be careful as connector break off easily thus requiring a new stack flue sensor...
I accidentally discovered this when I turned the board upside down and spotted the LED red light on indicating a fault with the SFS**
I wish some one would tell us how to by-pass the stack flue sensor to make the heater work.
Good luck...hopefully the power button is close by and your board is working....
6/11/2010 9:42:15 PM •
Sta Rite...
•
Answered
on Jun 11, 2010
Can a SR400NA be converted to a SR400LP and if it
Their is a loop in the gas line inside the heater. It's an invereted "U" and has two unions on it. Remove the unions and pull the loop out. In one of the unions their is a control disc. All you need to do is replace this disc. The number for LP is; For the LP orface kit 77707-0441, and for the N/G to LP conversition kit is 77707-1441. I don't realy know the difference but I would think the latter would come with "O" rings that you need and such. As far as cost, I don't know. Every time I bought one my supplyer would give me one when I needed it and I would give them back the N/G part. This link should get you to your owners manual.
http://www.pentairpool.com/pdfs/MaxEThermOM.pdf
Good luck and remember, gas burns. LP is heavy and will sink where N/G is light and floats away.
5/15/2010 11:38:50 AM •
Sta Rite...
•
Answered
on May 15, 2010
Not finding what you are looking for?