My Lexar 2GB flast drive
I wish that I could provide hope. Unfortunatly when this device is dead it is dead.
3/23/2011 1:51:23 AM •
Lexar...
•
52 views • 0 helpful votes
It says my card is
Hello
OK, if the memory card itself is locked, you might
sometimes get this error code. All you need to do is to take out the
memory card and switch the lever on the left side to the unlock.
If
the error is still displayed after you did the above, you might want to
try the card in another camera.
If
the card works in another camera . the problem is with your card reader
in your camera.
If you open you sd slot and look inside with a
sharp light , you should be able to see on the left side of the slot
there is a little copper or spring steel lever switch. This switch work
as follows:
1. When no card is inserted / no write protection ,
the switch is open and thus the protection is off.
2. When locked
card is inserted , the tab is depressed and tells the camera that the
card is lock.
Contrary to popular belief ,the little tab on the
sd card is not an electronic switch and does not physically influence
the card operation itself. If you put a locked card into a camera
without a sd lock switch , you would still be able to use the card
normally.
It is incredible difficult to fix this switch because
of space limitations in the sd card. Look into the sd slot and if you
can see the switch , use a needle to pull the little tab down toward the
base of the camera by about 2mm or until it works being careful not to
bend it.
If this does not resolve your problem , there might be a
short in the switch circuit and the camera will need to be disassembled
to resolve this error. This should cost no more than $50.
Please
feel free to contact me if you need further information
Kind
regards
Andrea
1/19/2011 8:21:39 PM •
Lexar...
•
115 views • 0 helpful votes
It seems that i can't put anything on my Echo ZE.
Hello,
b>
b>I think it could be due to virus activity. Some virusmake the contents of the drive hidden, that's why user can't see the
files and the space available for use is less than thecapacity and also can not open the drive.
It issuggested that go to FOLDER OPTIONS - and select SHOW HIDDEN FILES. It may showthe hidden files.
If can not show ,hidden file (tools >folder option>view> check on show hidden file>check off hide protected and checkoff hide extension) now can see all hidden file in c drive. If not think......
For ensure again
run>type> msconfig > hit can not open ms config if virus effected
run >type> regedit>hit>can not open registry if virus effected
run >type >gpedit.msc>hit can not open group edit policy if virus effected
Otherwise, ifyou don't have any vital data on the drive, just format it in another pc.Pleasenote, before insert the
Pen drive .Go to run command from start menu OR
Press Win key+R and type gpedit.msc and hit>Usser configuration
>system>turn off auto play >enable>use down arrow key select all drive >apply >ok. Control panel>administrative tools > service>select any word in right side and presss for select Shell Hardware Detection> d -click >use down arrow key>disable >start. And now can insert pen drive and format. Hope this wouldfix the issue and
.
Youshould fully scan by f-secure bootable cd or any another antivirus bootable cd.Just insert the disk and restart.
Follow bellow the download link.
http://www.askvg.com/download-free-bootable-rescue-cds-from-kaspersky-bitdefender-avira-f-secure-and-others/
you wouldbe able to enjoy the full capacity of the disk. Try to be sure follow these youshould delete partition and create new partition and format your all drive.
Now install fresh O.S.Hope it will help you.
I can download music from my PC on to the
It could be the MP3 player doesn't recognize an 8 gb card... try a smaller one
OR
The SD card could be bad... try it in another device you know suuports an 8 gb card
Lexar 8GB wont work. when i insert it, it shows up
Some computers will not support a large 8GB stick. The best some will do is 2GB, If you are running a computer pre-2001, you may not be able to use the 8GB stick (I have the same problem with my desktop PC). It just is not supported!
10/5/2010 8:56:39 PM •
Lexar...
•
1,036 views • 0 helpful votes
I have inserted the lexar card reader into the USB
Go into "My Computer" and locate the card reader drive icon. If it's not there then you need to load its' driver. If it is there, merely double click on it to open the files contained in the card.
12/13/2010 11:58:05 PM •
Lexar...
•
92 views • 0 helpful votes
I have a lexar 32mb
go to computer right click on the card & select farmat & farmat it
11/22/2010 6:30:17 PM •
Lexar...
•
127 views • 0 helpful votes
When we put in the
if your system makes a connection with the device on plugin , you should here a dual toned sound indicating its been plugged in and recognised. if you here this and still dont get a popup. the device can be found by opening my computer link in start menu and then selecting the removable or flash drive icon usually listed last in the letter labels. c: being your main hard drive and so on.
One day my SD card was fine and full of pictures
You may need to try some photo recovery software to rescue the pictures, here are some for your option. You may not recover all the pictures, but will recover most of them.
Photo Recovery (for Windows)
Photo Recovery for Mac
Both programs are able to recover pictures, videos and music files.
Note: Before your files are recovered, do not attempt to save more files to the memory card or stick in case the original lost files are overwritten.
Lexar USB stick use to
Usually this is and issue with the usb host to pci bus driver check the support website for a new one. PS usb 2.0 function usually doesn't just stop working on the flash drive itself
Needs to format and I
Hi
To format it Connect it to the computer, go to My computer-> right click on the mp3/mp4 player after it is displayed-> select format-> Format it as FAT32 File system. Formatting the MP3/MP4 player will delete all the songs/data from the player. So, backup all data before formatting it. Hope this helps...
Daniel
I have a jumpdrive4usbgb. I
insert the jumpdrive in your desktop pc and copy the contents from the pc to the jumpdrive...
then insert the jumpdrive into the laptop pc and then copy the contents from the jumpdrive and paste it in your laptop pc at the specified place..
When i switch it on it says incorrect format
Sounds like a format error on the storage. The bad news is the tunes stored on it are probably gone.
Do you have a mini USB B cable that you can connect to a PC? With this you can reformat the internal memory and the SD card.
Good luck.
Plugged in memory stick,coputer said
The computer see the Lexar as a external storage device.
Just click on My Computer and you will see the Lexar as a E drive or some other drive letter. Double click on this to open the drive. You can create folders on this drive and copy and paste files to this drive or to the folders just like copying and deleting files on the C drive.
Put new lexar sdhc 4GB memory card in my canon
see if their might be some photos or file saved that you may have edited on the card maybe Microsoft visual studio's photo shop save to hard drive. delete with photo software and format put in camera format again. if it works with computer and not with the camera not compatible try another card
7/4/2010 2:30:21 AM •
Lexar...
•
563 views • 3 helpful votes
Not finding what you are looking for?