20 Most Recent Siemens SpeedStream 4200 (13A4200001) Bridge - Page 5 Questions & Answers

ok i give u a short and easy answer 

download a hardware software that atomically check your all computer hardware and download all hardware drivers atomically that u need to install. 
download from:

http://www.download3k.com/DownloadLink1-DriverMax.html
http://innofiles.com/soft/dmx/drivermax.exe

when ya say done everything what ya mean bud????

try this LINK

You need ethernet for this. No router I have seen in all my years of networking will accept a USB plug

usually for vista it has compatibility issues w/ drivers, u need to right click the driver on the c drive then click run as windows 98, me, xp.. just click on yes if it says unknown device or disk. or u can procees to speedstream site then download appropriate driver.

Usually you can keep the same modem. Who were your old and new providers? You should be able to go the the new providers website and get all the necessary settings to configure your modem to work on their service.

You cant connect 2 computers without any additional equipment. U can go for router to connect more computers.

Take care

Yes and No! The 4200 gives you the option to connect via USB or Ethernet. You can only use one or the other to connect. You have two options. The first DOES involve another "gadget". The second does not!

Solution #1

I realize you're not looking to use additional equipment, but a network hub, switch or router will give you what you need. You can pick up a very inexpensive router for under $50 or even better a wireless router for a few bucks more.

I recommend a Linksys Wireless Router (Model - WRT54G) as it is very user friendly and comes ready to use. Just connect the port labeled "Ethernet" to the "WAN" port of the Linksys Wireless Router. Then connect both of your computers to any of the four "LAN" ports.

Solution #2

You can connect the first computer directly to the 4200 via USB and connect the second computer directly to the first computers ethernet port using a Network Crossover cable. Without a router of hub between the two computers, a crossover cable is required to allow them to talk to each other.

Once you have them connected to each other, on the first computer open the network connection properties for your internet connection (will be the one setup during the install of the USB modem) and click "Share This Computers Internet Connection".

Now the first option is surely the most reliable and keeps the traffic separate.

Hope this help!

Did you try using the ip address of 10.0.0.1 ? I’m happy to assist further over the phone at https://www.6ya.com/expert/lou_afa492c634393790

When the V300 Line/Phone led flash in alternating fashion, it's telling you it's WAN connection is dead. The WAN light is off too. so internet and VoiP phone will not work

When the V300 Line/Phone led flash in sync, it can't register to the SIP server.

The V300 does not appear to be listed on the Mynetfone website though. Have you checked to see that your V300 has the latest Firmware. LINK

It may be that the V300 is not getting it's IP renewed. Can you alter the IP lease time? Do you have the V300 set up for PPPoE, or do you have it set to static or DHCP (refer CH4, page 25)

Hi,
I got ur question, try following steps and i hope it may solve your problem soon and also reply back to me if it solves the problem:

1. Hard Reset the Modem(on back side of modem or underneath you will find the small hole that says reset you need to press and hold that button as soon power light on the modem flashes release the reset button)

2. Go to control panel then go to network connection> on leftside click on create a new connection>click on next>select the first option Connect to Internet>next>select second option set up my connection manually>next>select second option connect to broadband connection that requires user name and password>next> typpe your internet user id and password and confirm the password>next>click on Finish..

3. You will get a new window with your connection name just click on connect at the bottom of that window, you will get connected OR you ill get some error if you wre not be able to connect, note the error if you get that there.


4. open internet explorer then browse the internet if you are connected....

5. If You face any problem reply back to me here with your ip address,dns server,default gateway so we can try to put manuall address on your modem.

6.Other thing that you can try is cick on start>> go to Run box>> Type>netsh dump>> click on ok>> wait for 2 minutes th reboot your computer and try to connect through connection that you would create in network connection.........



reply back to me pls........
navjot

you need to log on to portforward.com shoose router, choose game then follow instructions on how to open port 10400    to 10499 as well as udp 3658                       Adnan 

If you will have the new modem and the same problem will occur, then you can say that it could be a fault with the phoneline or if it is with the old modem.

It is a ADSL Modem. It should have all ports open. In order to set a EXTERNAL static Ip address, you would have to call up your ISP and ask for a static IP address.

What's your OS, what is your Computer ??? what are using at the HUB??
Aloha
Bob

Have you tried to Config, whats your ISP, what computer, and OS are you running, how far are you from the DM
Aloha
Bob

open up ports

yes u can!!
however ur going to need a cable called a CROSSOVER cable to connect the modem to the router. you can find this at any computer part supplier near u.
however u MUST connect the computers to the router with normal Straight through cables. plug in n enjoy!

Hi,

Please goto the below link and select your game and see the document for portmapping.

http://portforward.com/english/routers/port_forwarding/Siemens/4200/4200index.htm

With Regards,

TPV