Top 20 Siemens SpeedStream 4200 (13A4200001) Bridge Questions & Answers

First unplug the power cable from your modem. Then press and hold the power button of your modem for at least 1 minute. Then plug in the the power cable and wait until all the lights become stable. Then you can try to go online to check.If after this step you will not be able to go online then contact with your ISP provider. For More information you can call at +1-877-255-3353 or visit our website http://fixsmith.com/

Hi! For the problem your describing, it seems that your problem may be faulty hardware. I've found that the router that your ISP (internet company) provides to you when they setup your internet don't tend to be the most reliable and highest quality, but Siemens is a pretty big name. One thing I would try, which Windstream may have talked you through, is resetting your router. This will reset your router and WiFi, which means the name of your WiFi will be reset, including your password.

Look on the back of the router. You will see 5 different ports back there: DSL, Reset, USB, Ethernet, AC/DC, and I/O. You're looking at the reset button. You need a pencil or something thin. Stick the pencil inside to the reset button, and continue pressing the reset button for 5-10 seconds. Your router is now reset. Now, see if your problem persists.

If your problem does persist, most likely your problem is a faulty router. In that case, I would call/contact the hardware manufacturer, Siemens, and see what they have to say.
http://www.usa.siemens.com/en/contact.htm
Hope this helps. Thanks for using FixYa.

This likely means that your DSL modem is not trained up with the DSLAM. - Geek talk for your modem is not connected to the phone company's equipment properly.

1.) Remove power from the modem

2.) Remove all devices (including the DSL modem) from all phone jacks in the house.

3.) Add the DSL line back to the wall jack, taking care to plug the wall jack into the correct jack on the DSL line. (Do not use a DSL filter on your modem!)

4.) Power up the modem/

Still not working? Continue...

5.) Try a different phone jack

6.) Try a new phone cable between the wall jack and modem

7.) Call the phone company for further assistance.

If you want to get password for wireless connection then follow below procedure. Connect your router to computer with ethernet cable then you can access it with following default link. http://192.168.1.1 or http://192.168.0.1 or http://192.168.15.1 or http://192.168.2.1 If you are not able to access it with above ip then check your computers ip address gateway ip is your router ip try with it. Then it ask for user name and password. Type user as "admin" and password as "admin" or "password" or blank. Then you can see configuration page of router. If you are still not able to access router with above ip then you need to RESET it for that press RESET button for 10 seconds it is in back side of router then all settings defaults..Then you can access it with above method. . Then click on wireless->wireless security->WEP security there is code password note down it or enter new password then save setting s and restart router. then you can connect wireless with new password. Let me know if you need further assistance. Thanks for using FixYa.

hi you can check the internet connections at ip-details.com and check the internet speed in http://www.scanmyspeed.com/

No the alternating flashes mean it's in reset/programming mode. go into the interface and set it up properly.

To reduce the NAT

1 ) Disable the firewall in the router

2) Enable the Playstation in the DMZ

3) Make sure UPnP is Enabled

Resetting modem to Factory Defaults
Using the tip of a ballpoint pen or unfolded paperclip, press and hold the Reset button located on the bottom of the router. The pwr LED will blink red once, indicating that the reset has begun. Continue depressing the Reset button for four seconds or until the pwr LED begins to blink alternating red-to-green. Release the Reset button.
Set to bridged mode
Should now be on http:\\10.0.0.138 Click “Login” option. The “Username” is admin and the “Password” is admin. Then click “OK”. Click the “Setup” option and then click the “WAN interface” option. If asked for a Username/Password use admin/admin Click under VC heading the “8/35? option. Click “Next>>” The PPPoE option should be selected and then click “Next>>” again. Under the heading “PPPoE Type” select the “Bridge only” option and then click “Next>>”. Click “Finish”
A reboot is required before the new configuration takes effect. Click the word “reboot”. An additional “Reboot” button will be displayed. Click this “Reboot” button”

Hi,

Check out these tips...they can help you figure out whats going wrong with your refrigerator and why it is not cooling

Refrigerator not Cooling or Fridge not Cooling

How to Defrost Refrigerator Defrost Timer Problem

Water Running in refrigerator from Freezer

heatman101

Yes:
http://www.thevoipstore.net/speedstream-4200.php

You can change this setting in your router.

the password is admin also

Go here to download that

http://subscriber.communications.siemens.com/subscriber_networks/support.shtml

There are plenty of good routers to pick from, but the choice you make depends on more than your DSL modem and computer. It depends on your wireless network needs.
What kind of structure are you working in?
How many floors do you need coverage on?
Do you plan to play any multiplayer online games?
Do you plan to stream video or audio media on your network?
Do you need to setup access to your network from the internet?
How important is your network's security?

All of these factors are key in deciding the best solution.

Cheap is never the best deciding factor. The average cost for a decent reliable router will range in price from $50 to $150 depending on features.

Try plugging into amother power socket. If same modem is probably blown. Especially if there was a recent storm.

http://www.transact.com.au/documents/Speedstream4200_modem_walkthrough.pdf
this here is a full guide to do the job ..with pictures,,indications and links...I hope it will be enough ..and what you needed..
have a nice day !

go to the link below it is all explained step by step there. http://www.thevoipstore.net/how-to/setup-an-optus-speedstream-4200-modem-in-bridge-mode.html

it is possible but the router must be connected hardwired to your DSL modem.

The picture showing here looks like a speed stream modem. You will need to install your ISP software so the system knows you have an account with them (if this is a new service for you). If you've had the service for a while, but had your computer worked on, as long as all the ports work, you should be able to just plug and go. Your username and password for your ISP (Internet Service Provider) are memorized inside the modem, so as long as you haven't shut it off, you shouldn't have a problem.

http://support.xbox.com/support/en/us/nxe/kb.aspx?id=958431&lcid=1033&category=xboxlive

Here is a link to x box,hope this is helpful