Dream Maker Spas Dream Maker Ez Spa Hot Tub - Page 3 - Answered Questions & Fixed issues
Jets are not working
Your motor may be locked up or you may have a bad starting compasitor. Remove the cap on the back of the motor and see if you can spin it freely. If so check the compasitor. (a black plastic one will have a small cut out where the wires go. If it's black or blown out it's bad. A silver one will bubble out at the ends. If you can't tell set it on a table, flat bottom down, if it rocks it's bad. It should sit flat) If the motor doesn't spin freely pull the pump out and take the wet end off of it. Once the wet is removed if it spins freely your motors fine and you need to replace the seal and more than likely the impeller you just pulled off that has a split shaft.... This is caused by a pump seal leak going unchecked.
Just purchased a used Dream Maker X400 hot tub.
Have you opened the equipment access door and looked in it while it is running. I would look at the pumps to see if one of the seals are leaking. They will leak more on high speed and if you have a cir pump that runs the filter and an additional pump for high speed jet action it would make sense why it is leaking more while you are using it.
Hot tub run on hgh for 7 mins or so then shuts
Was your motor just replaced? I see this issue from time to time. It is caused by the pump overheating. You've either got clogged vents, very rare unless you have a rat problem in the spa, or your motor was replaced with one that has less hp.ex. Either a spa repair company trying to make more money, or a home owner trying to save money deside to replace a 2.5 HP motor with a 1.5 HP motor with out changing the wet end. Now you have a smaller motor trying to push the origanal imperller. Result is motor overheats, thermal overload kicks the motor off, motor cools and comes back on to start the cycle over again.
Code so when runs keep shuting off then over heat
not too familiar with that brand. If so is error for overheat check filters or run it without. filters could be clogged and is a common cause of overheat error code. Check circulation pump and make sure its working. Also if you recently drained and refilled you could have created a air lock that doesn't allow the pump to move water and its easily fixed by loosening the discharge end of the pump until the air comes out....you will notice it right away
Sunrise spas
Mine is brand new and won't either! Did you get it fixed?
Balboa vs500
Your economy spa is equipped with a hot stick. This "hot stick" is nothing more than a PVC manifold
that forces the water through multiple 1/2" ports that creates enough
friction for the water to heat itself. YOUR HOT TUB HAS NO HEATER. The benefit is that there is no heating element to corrode and replace. The down side is that it takes
quite awhile to heat the water. If you start with water that is 55-60 degrees it will easily take 48 hours to hit 100
degrees. Keep in mind that is dependent on the outside air temperature. Good luck with that!
When i plug in motor humbs and then kicks bracker
More than likely you have it plugged into a standard wall socket and the breaker that the spa is on has other things like lamps or blenders on the same breaker. If you have a hot tub plugged into a standard outlet you need to be sure it's the ONLY thing on that breaker or else it will trip. Your outlet is 110 and that spa need 120 so it's pushing it to begin with.
How to I increase the temperature to 101 on the drreammaker spa fantasy model?
This may be a little late as you may have already found the answer. But most "Fantasy" spas have "Balboa" control system. They are either a heat control knob, or Up/Down arrows on the spa side control system. If you have the know & it is all the way turned to max position, and still not hot enough, then you may well have a faulty "Temperature Sensor". Get a replacement from your local DreamMaker dealership. Easy to replace.
I have a Coleman 400
check to make sure all the jets are open, this can cause a restriction, that makes the tub think its the filter
Not finding what you are looking for?