Top 20 Dream Maker Spas Dream Maker Ez Spa Hot Tub Questions & Answers

this car? https://www.facebook.com/InTheKnowInnovationAOL/videos/this-hot-tub-on-wheels-is-the-newest-party-vehicle/2427071604221605/

• not a car, moved yah
• ask the maker. for help/parts or all the installer for help.

google shows https://www.hottuboutpost.com/hydro-quip-6000-series-electronic-control-system-cs6209b-us-f/

What is this?

https://www.fixya.com/t26638542-3_jets_arent_working_model_.2_928w

when ever you fill the spa always fill it where the filter goes on just put the hose inside and let it do its thing filling up. After the skimmer is filled you should be able to fire it up, but don't run it with the pump dry or not primed you'll ruin it.

bad plug or broken wire replace

Change or adjust thermostat.

Hi as you know you are in the Sleep mode of your pump and filter settings. To change the setting to a different setting you must click on the temperature button followed by the light button. This will put you in the filter selection mode once there use the temperature buttons to toggle between the options. For more information you can look to this link. How to change the Filter Mode on Dream Maker Spa

Are you saying that it stops at 89°? It will not go any higher, even though you have the set temperature at 104°? If that is what you are stating, then you probably have a bad temperature sensor.

You may be in economy mode. Economy only heats the water during a programmed filter cycle. You want it to be in standard mode which turns on the hot tub once the water is 2 degrees below the desired temperature. There should be a mode or program button on your topside. One some systems you'll have to hit prog/mode button then the temp up button to change the mode. There is also a sleep mode. Never used it not sure what it's for.

I have not seen an ic error code. I have seen ICE several times. So either you do not have the original pack that came with the spa or your display may be malfunctioning. What is your hot tub doing while the ic code is pressent? Portable Hot Tubs and Spas On Sale

Thanks for the question! It could be several different issues. First, It's possible the topside jet button is malfunctioning and may need to be replaced. Is there any type of error message flashing on the topside display? Second, The pump may be bad, If it's a 2 speed pump it's possible to still circulate the water and maintain temp while the pump is malfunctioning. Depending on your level of "do it yourselfness" you may attempt to troubleshoot and repair it on your own. Checking for an error code on your topside is the best 1st step to take. I wish I could be of more assistance however, without being able to inspect it myself those are the best suggestions I can muster. Good luck & I hope I was able to provide at least some assistance. =)

remove front panel visually inspect pumps to see if leaking if ok check by control box remove cover inspect where plumbing runs through keep eliminating thing until you find it

ok, what exactly is your question?

OK, 5n is meant to say SN meaning sensor. This is refering to your temperature sensor, and means that the computer thinks that the sensor has failed.Check to see that it is plugged into the board completely, then verify that it is not chewed up by a mouse or rat. Both of these are the most often seen problems.Beyond that feel free to email me if you still need [email protected]

if its all wet, dry it out with a fan and then start your search, if it's under a pump, it is a shaft seal, a fairly cheap fix, i charge 20 to do it and I do some preventive measures to the pump so it can be serviced in the future without damage (smart). but it also might be a loose jet nut, they can be tricky to get at, but if carefully done can be tightened with a dull screwdriver and a hammer tapping on the edge of the nut. Hope this gets ya running again. ask if you need more help, and don't forget to vote if i was of help

26 Installing two pole GFI breaker I'm not clear on why you can't use a GFI Breaker. Has someone said this to you, or have you tried using a GFI and it didn't work? Does the heater run off 120 v or 240 v?

You can find the Leisure Bay Spas owners manual here. Leisure Bay Spas Hot Tubs Information