20 Most Recent
AEG 23 in. Favorit 44070Vi Built-in Dishwasher - Page 6 Questions & Answers
AEG favorit sensorlogic has no power.
Electronic is protected against short circuit throught out VDR - voltage dependent resistor which is located on the electronics. Unfortunately, when this happens usually get hurt some other component part or burn printed circuit boards.
Any intervention on electronics requires qualified person otherwise there is the risk of fire or electric shock.
Dado
Favorit 84470VI
Heater, 230V./2000W.-d.32mm.
The heating element, which is encased inside a tube, is used to heat the washing water. The heating element is not activated during the drying phase. Inserted into the delivery side of the washing pump and coupled with the duct which directs water to the upper spray arm.
Built-in safety devices: Two thermostats
First thermostat: auto-reset bi-metal thermostat calibrated to 98°C and connected in series to one branch of the heating element.
Second thermostat: manual-reset fuse calibrated to 206°C and connected in series to the second branch of the heating element. If this fuse intervenes, the heating element is disconnected definitively.
Dado
How do I fix problem F3 and spray arm faulty on my KO FAVORIT 8080
F3 - The anti-flood protection system has activated.
When in operation the fault message F3 appears in multi dispay:
- First close the water tap.
- Pull out the power plug.
- In the case of hard-wiring: turn off the electricity supply, remove the fuse and disconnect.
- Check float microswitch and float of styrofoam.
- Find and remedy water lakeage in the bottom of dishwasher.
Dado
How do I fix problem F3 and spray arm faulty on my KO FAVORIT 8080
F3 - The anti-flood protection system has activated.
When in operation the fault message F3 appears in multi dispay:
- First close the water tap.
- Pull out the power plug.
- In the case of hard-wiring: turn off the electricity supply, remove the fuse and disconnect.
- Check float microswitch and float of styrofoam.
- Find and remedy water lakeage in the bottom of dishwasher.
Dado
AEG OKO FAVORIT 40300 When switching dishwasher on no water is flowing into the the dishwasher?
It should first be checked for correct water inlet hose with safety valve. After connecting the double-walled water inlet hose, the safety valve is next to the tap. Therefore the water inlet hose is only under pressure while the water is running. If the water inlet hose starts to leak during this operation,
the safety valve cuts off the running water and the draining pump in the dishwasher is switched on. If the inlet hose with safety valve working correctly than could be some of following faulties.
- The door of the dishwasher is not closed properly.
- Mains plug is not plugged in.
- House fuse in defective.
- In the case of dishwasher models with start delay
timer: A start delay is selected.
If you look at the lower electrical diagram then you can see that all electrical components are located in a circuit inlet valve which can be also faulty.
- ON/OFF Switch
- Door switch
- Program controller (Timer)
- Pressure switch
- Inlet valve
- Float switch
- Wiring between all this components
Dado
How do I fix error .60?
The temperature must increase by a certain amount at each step.
If there is no temperature increase, the electronics will generate "Heating Time Out" or fault code i60.
In this case program will continue to the end without heating and the washing result will probably be unsatisfactory.
Could be: Heating element faulty; intervention of safety
thermostats (open); faulty wiring; NTC sensor (poor
thermal contact); insufficient water circulating in the
tub; washing faulty pump (impeller stripped); circuit
board faulty.
Dado
What means error .60?
The temperature must increase by a certain amount at each step.
If there is no temperature increase, the electronics will generate "Heating Time Out" or fault code i60.
In this case program will continue to the end without heating and the washing result will probably be unsatisfactory.
Could be: Heating element faulty; intervention of safety
thermostats (open); faulty wiring; NTC sensor (poor
thermal contact); insufficient water circulating in the
tub; washing faulty pump (impeller stripped); circuit
board faulty.
Dado
Not finding what you are looking for?