Top 20
Black & Decker RD1440K 85th Anniversary 14.4V Cordless Drill/Driver Kit - Page 3 Questions & Answers
Drills
It does not appear to be reversing. If it was it should have a lever right above the switch. Not worth much either since parts are no longer available to repair it.
When tighten, keyed drill chuck gets stuck
Did the left hand screw inside the chuck come loose? This happens a lot and when it does the screw will back out a little and block the jaws from closing. If not I use dry graphite lube.
How to unstick the chuck
Hi Gregory,You can use a 6 inch pipe wrench on the top of the chuck and an eight inch on the large part of the chuck.Put a rag in the pipe wrench jaws.Lay the drill on a flat surface with the chuck pointed at you.The handles face the same way,small one on the bottom to lock the chuck and the 8 inch on top so they look like scissors. Depending on which way the chuck is jammed will determine if the handles are on the left or right side.Gloves and safety glasses will make holding the top wrench with a bit of force to lock every thing in place.Now just a tap on the end of the eight inch wrench will loosen the chuck.If the set up is wrong you will only jam the chuck more. Thank you for choosing FixYa.
Black & Decker cordless drill 9.6V chuck will not come off shaft
If it won't close the only other option you have is to break the outer collar and use a chisel to hit on the exposed jaws inside the chuck. I have detailed instructions in the tip section on how to remove a chuck from these drills. Let me know if you need more assistance.
I have a Black & Decker 78-936 type 1 drill press.
there are detailed instructions for this at dewaltservicenet.com type in the model number as 78-936 and you can download the operators manual with detailed information. If I have helped you would you please vote accordingly and thank you.
I have a B&D Firestorm 18v 1-hour battery
Hi I have same problem with the charger. Solution is to replace the charge with new part number issued from B&D AustraliaNumber of 90515050-01 until stock runs out , then it is replaced by part number of 90578873 early to mid june 2013.Hope this helpsLance from Perth , Western Australia.
I pressed the button trigger
yep your right. time to look at getting a new one. dont run it anymore JUST NOT SAFE.
Best of luck
Tom
Hey would you tsake a second and rate us and if are reply was on spot :)
Should I be seeing a spark through the ventilation
not unusual to see sparks - could indicate high wear on com. If drill gets VERY HOT then suggest you take it to an electrical repair shop to have it checked out. If drill remains at a normal temperature then I would LEAVE WELL ALONE
My Black & Decker 0-1200
You have not mentioned a model number but look just above the drills trigger and see if there is a lever that moves under the drill above the trigger, that is the most common reverse switch location. The other is a switch on the top of the drive that slides back and forth to change the drill from forward to reverse and visa versa. If it is not in either location i will need the model number of the drill to look up the instruction manual.
I have two drills, two
I have to agree, I assume you have tried the the same battery on both chargers? is it possible that one charger ruined all the batteries? I wish I could offer some real help other then to say "hmm." But my best guess is that one charger ruined all the batteries. unless you use them both at the same time, then it would be hard to have them all quit at once.
-
The chuck is frozen on
Hi,
Yes, they are an inferior product. However you can replace the B & D chuck with a Jacobs chuck that will hold up and last for a long time!
Jacobs Chuckheatman101
Can a rechargeable battery be obtained for
I would recommend to check in your yellow pages under batteries. Ask them if they replace batteries in the unit that you have. Generally the batteries that come in cordless units are the cheapest units that die rather quickly. The replacement batteries have more power and longer life. And they are generally half the price of a new unit.
Cordless drill - model KC9682C
If light is on charger the charge is fine. You could verify using voltmeter it should put out = to what it says on the back of charger 12-18 volts or so.
Most likely battery is shot after 8 years they just dont' hold a charge anymore and they often will only charge for a few minutes when the chip in the computer tells the charger to shut off due to defective battery.
compare prices of new drills and new batterys sometimes new drill is not much more. Try ebay and harbor freight for ultra low priced batteries.
Not finding what you are looking for?