Top 20
Black & Decker RD1440K 85th Anniversary 14.4V Cordless Drill/Driver Kit - Page 6 Questions & Answers
Replacing the chuck on black & decker drill
remove the chuck retaining screw LH thread, and then find a bent handle allen wrench about the chuck capacity and insert the shorter piece in the jaws and tighten, Shift the tool to the low position (if it has one) and the selector to drill only (if it has one) position the chuck on a block of wood at about a 30 degree angle so you can strike it counter clockwise and hit it with a hammer, it might take a couple times but it will come off. Reinstall in reverse order,
I cannot get to registering my new cordless drill,
I finaly found a way to register the drill on the internet, I kind of blundered into it, so I got it registered. I don't think I could tell you how I did it. So I got it set up, I couldn't get ahold of any one on the phone either.
Interchageble cordless batteries
not likely most batteries may look similar, but will not fit in the wrong device. Also if it did fit it would burn up your motor quickly. is there a problem with the 18v set-up?
Regestering my new cordless CDC1800 dril
if this is a Black and Decker, go to their website at the name and then .com and in the header area you will find a link on the right side that will allow you to register the tool.
Need a charger for 24 volt B&D fire storm--
the charger you need is PS1MVC and you can buy it online from Blackanddecker.com if not look in you local phone book for tools and you might be able to get it from a big box store like Home Depot. Let me know if you need any more help
NEED REPLACEMENT 7.2 VOLT BATTERY PACK FOR B&D
I have tried 2 different sites for this model with no luck, I would suggest going to Dewaltservicenet.com and under service center locator or service locator typing in your information to locate one close to you so you can talk direct with them Sorry I don't have better information for you.
Firestorm Cordless Screwdriver. 10mm 14.4v
go to Dewaltservicenet.com and in the middle of the page towards the bottom type in your model number and it will direct you to another page where you should be able to find a manual. If you want to give me the exact model number I will find one but this is where I would go.
The motor fell apart and need to put it back
Get a large plastic bag and put all the pieces in to it. Shake bag for 10 minutes. Look into bag, has drill reassembled? If not, shake again for 20 minutes. If this fail to reassemble drill, throw bag into land fill, and buy a new drill. Thank you for your support of BD.
Need new brushes for 1983 black and decker hammer
I'd suggest calling the Customer Service line who can put you in touch with your local Service Centre or authorised repair agent. These items are classified as spare parts and generally need to be ordered in, dependent on availability - 1800 444 224
Can't remove the chuck on a drill.
There are one-way (non-reversible) and two-way (reversible) drills. Mine is one-way. Methods for chuck removal are different for these two types.
Procedure for one-way (non-reversible) drills:
Drills of this type have no chuck screw, so one have to hold the spindle with a wrench, than to sharply strike the wrench with a hammer to spin it off.
Procedure for two-way (reversible) drills:
Open the chuck up and in the bottom is a screw that holds the chuck on
the shaft.The screw turns in a clock wise motion to be removed and then
you can top the chuck off the shaft.
Is Hammer adjust collar attached to chuck?
I looked at a old schematic for the 5078 and it appears that it might come off after chuck removed. The chuck is threaded and if you have the 2 speed model, shift it to low and put a bent handle allen wrench into the jaws and chuck on workbench or block of wood with long portion at approx 30 degree angle and strike the handle, you will be hitting it counter clockwise to remove.
Chuck removal
There is a screw in the bottom of the chuck. It has a standard thread. Clamp the chuck in a vise, find a screw driver that fits as snug as possible, to prevent stripping the screw, remove the screw and pry off the chuck. An impact driver will simplify the removal, if one is available.
Black/Decker 12 v drill charger will not charge
If the battery gets warm after being in the charger a while and still is not charged, then the battery is bad
if the battery stays cool in the charger then the charger may be bad
Chargers usually have a light code, I.E. on means charged, slow flashing means charging, and a quick blinking means bad battery
Some chargers have 3 lights and the code should be imprinted on the charger.
hope this was helpful, cb
Not finding what you are looking for?