Top 20
Black & Decker RD1440K 85th Anniversary 14.4V Cordless Drill/Driver Kit - Page 7 Questions & Answers
Having problems securing masonary Bit on 3/8 Black&Decker Drill 7
If it's an inexpensive bit, odds are it's spinning in the chuck. If the chuck key can't tighten the jaws well enough, you'll need to borrow or buy a different drill (or you could replace the chuck).
If you bought an SDS bit (one with slots milled in the shank), you're best off buying a bit made for a standard drill. It's not impossible to get a SDS bit to chuck into a standard drill, but it's difficult and they often slip loose during drilling, messing up the hole.
Take care!
REGISTRATION OF DRILL
FixYa is not the one registering the tools, but you can go to BlackandDecker.com and in the header area on the right hand side there is a link to register your tools. I have had good luck with this
I have a B & D Professional 1965 and need to
u probuly got sumthin jammed in side it such as a piece of wood to metel sheres (that could be a real pain in the ***) u sho really assemble it and take it out then if dat never did it talk to the manufacter.
I have a very old 1960's B&D rotary hammer drill.
I have bad news for you, most of the parts for this tool are obsolete no replacement including the tune up kit. If you want to double check go to Dewaltservicenet.com and type in your model number.
Cant find registration site
The header says you have BlackandDecker.com and if so go to the site I just listed and in the header on the right hand side you will find an area for the registration. If I have helped you would you please rate my information accordingly and Thank you
Tool will not take a charge
It sounds as though it should have its last rights. Generally a battery will go dormant after awhile that is why even though you might not use the drill or tool you should charge the battery at least once a month just to keep the cells active.
Won't take a charge. batteries are good
why?
The charger is designed to charge all the batteries at once. The only suggestion is that you measure the voltage of each battery to see if it has charged.
It one or more are dead, this why the charger cannot charge them.
Unable to register
Had this question before, try this site Myblackanddecker.com and see if that helps, if not let me know and I will dig deeper into their files for you.
How to remove oven door Maytag mgr5775qds
To remove the oven door on a Maytag MGR5775QDS range, you can follow these general steps:
- Open the oven door completely to access the hinges.
- Locate the hinge locks on both sides of the door. These are usually small levers or clips.
- Use a flathead screwdriver or your fingers to flip the hinge locks toward the oven cavity, releasing them from their locked position.
- With the hinge locks released, close the oven door halfway.
- Lift the oven door up and off the hinges by pulling it toward you and lifting it away from the oven.
- Place the oven door on a flat surface, such as a table or countertop, to work on it or store it.
Remember to exercise caution when handling the oven door, as it may be heavy and awkward to maneuver. If you're unsure or uncomfortable with removing the oven door yourself, it's always a good idea to consult the appliance's manual or contact a professional for assistance.
2/17/2024 4:58:09 AM •
Drills
•
26 views • 0 helpful votes
How to remove the chuck for Black & Decker 4.5 Amp Drill.
Insert the short end of a 1/4" or larger hex Allen wrench into the chuck and tighten. Facing the tool strike the long end of the hex wrench sharply counter clockwise as it is a standard right hand thread. This will loosen the chuck so that it may be unscrewed by hand.
Oct 12, 2022
..
1/23/2024 5:21:27 AM •
Drills
•
28 views • 0 helpful votes
Not finding what you are looking for?