Washing Machines Logo

Related Topics:

Posted on Apr 13, 2008

Maytag mah4000aww motor control board bad cannot tell which series it is serial 53312313yk

1 Answer

Anonymous

Level 1:

An expert who has achieved level 1.

New Friend:

An expert that has 1 follower.

  • Contributor 1 Answer
  • Posted on Sep 10, 2010
Anonymous
Contributor
Level 1:

An expert who has achieved level 1.

New Friend:

An expert that has 1 follower.

Joined: Sep 10, 2010
Answers
1
Questions
0
Helped
900
Points
1

My front load washer is leaving water after done spin cycle can still ring water out of clothing....water is draining from hose and is spinning somewhat strange...like its not going through rinse properly sorta like its repeatedly doing same cycle pattern...spins for lil, stops makes running noses...spins sum more....soapy clothing...its 5 years old..but first time use this month finally connected it...when took bottom off to check hose connection noticed control board looked lil warped and brownish colored but not as meant to be..maybe its burnt out?

Add Your Answer

×

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

0helpful
1answer

Maytag washer MAH4000AWW timer will not advance. Washer will operate if I manually advance timer. Have changed timer, followed Drive System diagnostic test, the wax motor and control board were replaced a...

there is a motor inside the timer that turns the knob. the problem must be the replacement timer. was it a brand new timer from maytag or a 2nd hand? also double check your timer is connected correctly.
0helpful
1answer

Door light wont come on and dor wont lock, also replaced control board with new on and burned hole in it just like original

Hi, The wax motor of the door lock is the problem that is burning up the boards, replace the redish brown wax motor in the door lock assembly
0helpful
1answer

Maytag MAH4000AWW no longer does the high speed spin cycle. Other than that motor runs fine. Seems like a controller issue but don't have a repair manual to know for sure.

http://www.searspartsdirect.com/partsdirect/part-model/Maytag-Parts/Washer-Parts/Model-MAH4000AWW/3048/0153200/M0603006/00013?blt=06&prst=0&shdMod=MAH4000AWW

It could be the motor control board not telling the motor to switch to its highest speed, but it could also be control board not telling the motor control board to activate, but it could also be in the timing circuit. What other indications are you getting? Take a look at the wiring diagrams for this machine on the referenced site.
1helpful
1answer

Neptune front loader. doorlock light quit working. wont spin.

You will need to change the machine control board and door lock wax motor.
MAH3000AWW PART # 'S 22002988 AND 12002535
MAH4000AWW PART# 'S 22002989 AND 12002535
If yo look at your control board in the control panel you will find R11 burned.
3helpful
1answer

I have a burned out resister which I need to replace.

R11 = 3.9 K ohm 1/4 w If Q6 burned,change by NTE5657 ( 600v)
2helpful
1answer

Maytag Neptune washer model #MAH4000AWW, Press start botton starts filling then shuts off after a few seconds. Move to spin it begins draining then shuts off after a few seconds

Check out your motor control board near the floor on the right side. These have a high failure rate on the Neptunes. Maytag redesigned both the motor and motor control board to be more reliable. While inspecting this board, you are looking for a blown 10 amp fuse and /or burnt components. If you have either... then you will need the the new motor conversion kit which includes the motor, motor control board and the wire harness.

These kits are offered on the www.neptunewaxmotor.com order form and they ship UPS Ground.

This kit takes about an hour to install.


Don't forget to see the info on the website regarding the defective door latch wax motor that will eventually fail and damage your machine control board.



0helpful
2answers
0helpful
2answers

Neptune MAH4000AWW

If there are no errors then the motor controller thinks everything is ok.
Do you hear the motor spinning?

the belt in the back may be bad or jumped off.
If you want to look for yourself open the top panel.(3 screws in top rear)
0helpful
3answers

Maytag Neptune MAH4000AWW washer door will not unlock

no, the board and wax motor is one possible problem but more likely youll need the motor kit with spped control. even more expesive but prove to be a big problem with this washer
Not finding what you are looking for?

910 views

Ask a Question

Usually answered in minutes!

Top Maytag Washing Machines Experts

ZJ Limited
ZJ Limited

Level 3 Expert

17989 Answers

Brad Brown

Level 3 Expert

19187 Answers

john h

Level 3 Expert

29494 Answers

Are you a Maytag Washing Machine Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...