Maytag MAH2400A Front Load Washer Logo
Posted on Jan 25, 2009
Answered

Maytag MAH 24 does not drain and makes weird humming noise

My Maytag MAH 24 gave me an error message of "nd" and it did not finish through the rinse and drain cycle. I paused it and powered down and when I powered it back up it now just makes a weird humming noise. Since there is still some water in the machine, the door won't unlock and it won't drain/spin. Is there a re-set button on this machine so I can get my clothes out?

Answer This Question
  • 1 more comment 
  • thing1 Feb 20, 2009

    I have a Maytag MAH2400A Front Load Washer 2 years young now filled with water that won't drain during the drain cycle, and a door that won't unlock. is there a way for one to correct easily correct this?

  • everythingki Mar 23, 2009

    My washer is the same model, same problem, what is this? What's wrong? I tried moving the drain hose around, manually draining it and restarting the cycle after unplugging and after flipping the breaker. Anyone? 

  • Anonymous Apr 05, 2009

    I also switched to Tide toal care... my washer is 4 years old.

×

2 Answers

Anonymous

Level 1:

An expert who has achieved level 1.

  • Contributor 2 Answers
  • Posted on Mar 22, 2009
Anonymous
Contributor
Level 1:

An expert who has achieved level 1.

Joined: Mar 22, 2009
Answers
2
Questions
0
Helped
2950
Points
2

I also have this problem. to get the door to unlock, just unplug the washer and it should open in a min or two. you will hear a click. you may have a mini flood but at least you can get your cloths out and bail out the water. my problem started when i began using a new detergent from Tide called total care. Still tying to get the pump to work.

Anonymous

Level 1:

An expert who has achieved level 1.
New Friend:

An expert that has 1 follower.

  • Contributor 1 Answer
  • Posted on Jan 23, 2011
Anonymous
Contributor
Level 1:

An expert who has achieved level 1.
New Friend:

An expert that has 1 follower.

Joined: Jan 23, 2011
Answers
1
Questions
0
Helped
2372
Points
1

I have the same problem...How do you manually unlock the door so I can bail it out???

Ad

1 Related Answer

TheMazz

Kevin

  • 79 Answers
  • Posted on Oct 22, 2009

SOURCE: ND Error code

Error code "nd" means it is not draining. Click on this link to get the user manual:

http://laundry.manualsonline.com/manuals/mfg/maytag/mah24.html

Then click on "GET THIS MANUAL" to download the manual.

Not draining can be caused by the controller, pump, solenoid valve, or clogged drain.

If this information was useful, please select YES to the first to rating questios. Good Luck and thank you!

Ad

Add Your Answer

×

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

0helpful
1answer

Ou Maytag Neptune Washer MAH-3 will not drain.
This problem was answered a couple of years ago in detail. A search should produce it. Search the name Scruggs.
Read full answer
Sep 02, 2014 • Maytag Neptune MAH5500B Front Load Washer
1helpful
1answer

The washer ran fine then stopped with water not draining. When I push the on button I get a buzz or humming noise .nothing moves. There is no error code.
Sounds as if you have something doen in the pump preventing it from draining and in doing so shutting the machine off as a safety action. I think you can actually access the pump from the rear of the machine. just unplug the machine, prepare to get wet, take the back of the machine off, take the lines off the pump and check for the blockage.

If you need further help, I’m available over the phone at https://www.6ya.com/expert/jason_4570d45317834dd3

Read full answer
May 27, 2012 • Maytag MAH6700AWW Neptune Front-Load...
2helpful
1answer

Washer stoped and did not finish rinse cycle now it makes a humming sound and code nd
Washer Error Codes ND IS -No Drain There could be two problems...The drain could be clogged, or the water pump could be bad. Or the belt that runs the pump is sliping or broken
  1. Unplug the washer from the electric outlet.
  2. 3Open the case, and disconnect the water hose from the outlet of the water pump.
  3. 4If you get water pouring out from the pump, then plug that up and check the hose to the sewer. If that is clogged, then you have found the problem.
  4. 5Some washers have a self cleaning filter in that hose somewhere. Check that to be sure it is working properly.
  5. 6Reassemble hose from step 3.
  6. 7Plug washer back in. If it pumps out now, then you are done. If it doesn't, then the water pump is probably defective, so replace it.
  7. 8Reassemble washing machine case...you're done...
Read full answer
Oct 11, 2011 • Washing Machines
0helpful
1answer

My maytag washer mah-24 have a "nd" msg. which mean "not draining" and now i cannot open the door to take the clothes out. pls. help.
Unlocking the door:
Turn on the washer, but don't start any wash cycles. After a few minutes, the door should unlock itself.

Troubleshooting the "nd" message:
"nd" means "no drain". Empty the (now unlocked) washer and fill the wash tub with just enough water to see a bit of water at the bottom of the tub. Run a drain cycle and check a) if it drains and b) if there are any unusual noises while it is draining. If either event occurs during the drain cycle, the drain pump may have to be repaired/replaced.
Read full answer
Nov 25, 2010 • Maytag MAH2400A Front Load Washer
1helpful
1answer

Has 33 minutes and a error message of nd--maytag Neptune tl

What is the Model number of your machine if its a FAV6800A or FAV9800A please read on.

The ND error code means No Drain.

You could have a drain line clog or a stuck Pressure Switch contacts.

See this post for past troubleshooting;

http://www.fixya.com/support/t2209123-code_nd_fav6800aww_serial_number_10

There are links to the Service Manual and I go over how to put the machine in Service Mode to check that the Pressure Switch is signaling properly.

Do you want to DIY the repair?

Let me know.........Rich
Read full answer
May 19, 2010 • Maytag Neptune FAV6800AW Top Load Washer
0helpful
1answer

My washer stops before the rinse cycle because it can't seem to drain enough to start the spin cycle. I just had the drain motor replaced one month ago. I get the error code nd. I can sto the cycle and...
I'd love to say yes! The machine is stopping because it will not drain. This is what the nd code means. Therefore, it will not rinse (add more water) or spin because the water level is already too high and to try to "spin it out" would put too much pressure on the machine with that much water in it. Drain out the water by putting the drain hose below the level of the washer (this takes forever) and call your repair man back!
Read full answer
Feb 18, 2010 • Maytag MAH8700A Front Load Washer
7helpful
1answer

ND Error code
Error code "nd" means it is not draining. Click on this link to get the user manual:

http://laundry.manualsonline.com/manuals/mfg/maytag/mah24.html

Then click on "GET THIS MANUAL" to download the manual.

Not draining can be caused by the controller, pump, solenoid valve, or clogged drain.

If this information was useful, please select YES to the first to rating questios. Good Luck and thank you!
Read full answer
Oct 22, 2009 • Maytag MAH2400A Front Load Washer
0helpful
1answer

Error "nd" trouble
Nd, means no drain... a blockage in the drain line from the tub. Access from the back panel, you can remove the hose from the machine and check for blockages... this would be on the tub side of the hose... take the hose loose from the machine and check for blockage at the tub. squeeze the hose to check for blockage within.
take the hose loose at the pump to check for blockage there as well... watch out for water ...be ready to mop... let me know how you do..
Read full answer
May 26, 2009 • Maytag MAH2400A Compact Front Load Washer
0helpful
1answer

Washer wont rinse
we had the same problem with ours....nd means not draining and that means that there is something, probably coins stuck in your drain hose. pull the drain hose out and check it for change and make sure something isn't stuck.
Read full answer
Jul 21, 2008 • Maytag Neptune MAH9700 Front Load Washer
1helpful
1answer

Nd error essage
nd= no drain. loud buzzing noise sounds like something stuck in pump assy.remove the door(2screws) adn other 2 screws oppisite side, and hte front panel comes off giving you acess to the drain pump, pull the hoses and look for the obstruction
Read full answer
Mar 14, 2008 • Maytag Neptune MAH5500B Front Load Washer
Not finding what you are looking for?

View Most Popular

MAH2400A Front Load Washer

  • Washing Machines

Related Question

Ou Maytag Neptune Washer MAH-3 will not drain.

  • Maytag Neptune MAH5500B Front Load Washer

Related Topics

2,382 views

Ask a Question

Usually answered in minutes!

Popular Questions

Washer leaking water from bottom

Maytag Atlantis MAV6000 Top Load...

Maytag Neptune Error COde "nd"

Maytag Neptune MAH9700 Front Load...

Want to disengage lid lock on maytag centennial

Maytag Centennial 3.2 cu. ft....

Maytag 2000 series shows error code f6 e1. How can I fix?

Maytag MHWE200XW Washer

Maytag maxima codes F06 and E02: Tried doing a spin/rinse/drain on an empty machine. Timer seems tpo be working but cannot hear water filling or barell spin. tried to shut off and door is now locked.

Maytag Maxima EcoConserve Series...

Top Maytag Washing Machines Experts

ZJ Limited
ZJ Limited

Level 3 Expert

17989 Answers

Brad Brown

Level 3 Expert

19187 Answers

john h

Level 3 Expert

29494 Answers

Are you a Maytag Washing Machine Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

PDF Manual
. MAH2400A Front Load Washer Manual

MAH2400A Front Load...

Loading...