20 Most Recent Maytag EPIC MFW9600S - Page 4 Questions & Answers


bad motor if no voltage to motor bad control board

Maytag Washing... | Answered on Apr 27, 2019


blocked or faulty pump,some models are belt driven so then a broken belt

Maytag Washing... | Answered on Apr 22, 2019


F24 indicates a water temperature sensor error. If during the wash cycle in the water-heating step, the water temperature sensor (NTC) value is out of range the F24 error code will display. Possible causes: Too cold of water or hot water is turned off.

To access, you will have to UNPLUG your washer and remove the lower access panel under the door. The panel comes off by removing the screws under the bottom edge. HINT: If you place a 2 x 4 under the front feet of the washer, it will make access to the screws much easier. If the panel sticks, a tap on the sides will knock it free. The panel will drop down then come off. The sensor (NTC) is located at the base of the wash tub in the front on the heating element. This will be a small square shaped plug between the heating element terminals. Make sure this plug is secure and not loose or unplugged. It is common for the connector plug to come loose due to vibration. If the plug is intact, check the contacts for corrosion. If everything appears as it should, then unplug the wire harness and take a resistance check. Readings will be as follows:

Temperature Meter Reading
32°F (0°C) 35.9 K ohms
86°F (30°C) 9.7 K ohms
104°F (40°C) 6.6 K ohms
122°F (50°C) 4.6 K ohms
140°F (60°C) 3.2 K ohms
158°F (70°C) 2.3 K ohms
203°F (95°C) 1 K ohms

Roughly...around 9K ohms at room temperature if I'm reading the chart correctly. Take readings as listed and also double check the connector to make sure it is not oxidized. Try cleaning the plug and reconnecting to see if the error code goes away. If not, you will probably have to replace the sensor. If the sensor checks good, take a reading across the heating element terminals. It should indicate about 15 ohms.

Lastly, remove the washer top panel by removing the three screws holding the panel in place in the rear. Once the screws are removed, slide the panel back then off. Locate the Central Control Unit (CCU) directly behind the wash tub. Take a resistance check at the Heating Element Solenoid by removing connector 9 from the CCU (this is the second connector from the RIGHT as facing from the front). A reading across test points 1 & 2 should also read 15 ohms.

Maytag Washing... | Answered on Apr 18, 2019


CHECK HOSE SCREENS THEN REPLACE THE INLET VALVES

Maytag Washing... | Answered on Apr 18, 2019


<https://www.maytag.com/washers-and-dryers/washers/front-load-washers/p.epic-z-high-efficiency-front-load-washer.mhwz600tw.html>
I NOTICE IT READS - TEN YEAR WARANTY ON PARTS.
LINK MAY PROVIDE PHONE CONTACT.

Maytag Washing... | Answered on Apr 05, 2019

Not finding what you are looking for?
Maytag EPIC MFW9600S Logo

54 questions posted

Ask a Question

Usually answered in minutes!

Top Maytag Washing Machines Experts

jimorris77

Level 3 Expert

411 Answers

Sheldon Dedek

Level 3 Expert

909 Answers

Bill Long

Level 3 Expert

606 Answers

Are you a Maytag Washing Machine Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

View Most Popular

Maytag Washing Machines

  • Maytag Washing Machines

Most Popular Question

problem f02 error

  • Washing Machines
Loading...