20 Most Recent Maytag EPIC MFW9600S - Page 2 Questions & Answers


This is actually a fill error, it appears when the tub should be filling and is not being sensed. Make sure that both hot and cold water is turned on. Since you do see water coming into the tub this is an issue related to your pressure switch. It sounds odd but this can also be caused by a siphoning drain so check to make sure your washers drain hose has only a little over a foot into the drain otherwise this may cause it to siphon and throw up the same error. If the water is on and the drain hose checks fine then I would guess your gonna have to replace the pressure switch but right now my money is on the drain hose being shoved to far down in the drain pipe. Hope this helps.

Maytag EPIC... | Answered on Jan 30, 2010


if this wont drain then the drain pump is either seized or faulty if you have no power their then you have a faulty control board

Maytag EPIC... | Answered on Aug 21, 2009


(((FH)))


If after 30 seconds the control does not detect water entering machine and then valves will be turned off and the error code will be displayed.
Or
If the control has turned the water valves on and after 8 minutes the flow meter has detected 10.5 gallons of water passing through it, but has not detected the pressure switch trip, the valves will be turned off and the error code will flash.

Press PAUSE/CANCEL twice to clear the display.

Potential Causes

• If there is no water in the unit:
- Make sure that both valves at the water source(s) are turned on all the way.
- Check for plugged or kinked inlet hoses or plugged screens in the inlet valves
- Verify inlet valve operation
• If there is water in the unit:
- Verify Drain pump operation
- Pressure Switch Hose is in good condition and properly connected to Tub and Pressure switch

• Verify there is not a siphon problem
• Verify wire harness connections to; Inlet Valves, Pressure Switch, Drain Pump, Flow Meter, and Central Control Unit (CCU)
• Check all hoses for possible leaks
• Verify pressure switch operation
• Verify flow meter operation
• Verify CCU operation

Replace failed component.

Maytag EPIC... | Answered on Jul 28, 2009


The filter is located inside the unit. it is directly connected to the drainage hose(external). its inside the unit on the back, left side. i would also check the following as well to combat this issue.

1. Clogged drain line or water pump
Check to see if there's something stuck inside the pump or the drain hose connected to the pump (pump is usually located at the bottom and towards the back of the washing machine).

2. Water Pump
If the drain line isn't clogged, you may have a problem with the water pump such as a frozen pulley or a broken impeller. If that's the case replace the water pump. Note: if you have a belt driven washer, check the belt(s) for cracks, as this would be a perfect time to replace the belt(s) if needed.


Maytag EPIC... | Answered on Jul 20, 2009


HI. this F-1 error concerns the actual Electronic control board. it is malfunctioning at this point. this board cannot be repaired and, you will need to replace the entire control in this case. it has failed.

The unit will be inoperable without a functioning electronic control module. replace it asap if possible.

Maytag EPIC... | Answered on Jun 17, 2009


press and hold the signal for 10 seconds.
bit late huh.

Maytag EPIC... | Answered on Mar 31, 2008


you will have to take off the front off washer to put it back correctly.

remove the top panel 3 screws in top rear
remove the bottom panel 3 screw in bottom front
remove the top led control panel 3 screw or more along front lip
if you disconnect any wiring mark it well .
now the front of washer can be removed with or without the door (your choice)
careful with the door lock wiring.
be sure to unplug the washer.
while you are in the innards its a good time to wipe around the drum any buildup of soap etc..
and to clean the filter trap in the bottom access tube below drum.

Maytag EPIC... | Answered on Mar 31, 2008


Make sure it is plugged into a GFCI outlet; try adding a surge-protector. The fuse will blow if the power exceeds the rating on the fuse. (If a surge-protector on the GFCI outlet does not prevent this, there will be a problem with the wiring inside the machine.)

Maytag Washing... | Answered 7 hours ago


inside agitator 7/16 bolt remove and lift out and plate

Maytag Washing... | Answered on Oct 10, 2019


check to see if drained or spinned out

Maytag Washing... | Answered on Oct 10, 2019

Not finding what you are looking for?
Maytag EPIC MFW9600S Logo

54 questions posted

Ask a Question

Usually answered in minutes!

Top Maytag Washing Machines Experts

jimorris77

Level 3 Expert

411 Answers

Sheldon Dedek

Level 3 Expert

909 Answers

Bill Long

Level 3 Expert

606 Answers

Are you a Maytag Washing Machine Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

View Most Popular

Maytag Washing Machines

  • Maytag Washing Machines

Most Popular Question

problem f02 error

  • Washing Machines
Loading...