Top 20 Fisher and Paykel Aquasmart wl80t65c - Page 3 Questions & Answers

Are you in QLD on the Gold Coast

Fault code 49 is water valves, But the Aqua-Smart board is outputting the wrong code here, The Smart pump has blown the water valves fuse, A common thing in Aqua-Smart Machines. The Smart pump has jammed with lint and caused over current to the board and taken out parts on the board that drive the pump. Best to get a new/recondition board for your machine.

Fault code 49 is water valves, But the Aqua-Smart board is outputting the wrong code here, The Smart pump has blown the water valves fuse, A common thing in Aqua-Smart Machines. The Smart pump has jammed with lint and caused over current to the board and taken out parts on the board that drive the pump. Best to get a new/recondition board for your machine.

Unless there's damage to the machine it is the load. Make sure you aren't washing to small of a load. People do not realize how fast washers spin to extract. Just like they use tiny weights to balance your car tire, it only takes a little bit of weight to unbalance it.

Error code 245 is pump stall.If the 1.6amp glass fuse has blown, the five mosfets on right side have shorted out there legs & blown the fuse.Also check the pump drive parts for shorted legs.There are three resistor that burn out near the fuse.I will up loaded some pictures later.

You need to size set the LCD panel to your motor controller. 1. Press and hold the left SCROLL button,Then press HIGH EFFICIENCY button until two beeps are heard. 2. Press the SCROLL button to select machine size (600 for WL70,650 for WL80). 3. Press the POWER button to set in memory.

Try to get a Rotor position sensor as they are cheaper. 105. (01101001) Comms Error Time Out These faults are reported when the Display Module detects an error in the communications between the Display Module and the Motor Control Module. Primary Source: Display Module. Action: Replace Display Module. Secondary Source: Motor Control Module. Action: Replace Motor Control Module. Tertiary Source: Rotor Position Sensor Action: Replace Rotor position Sensor. If this corrects the fault refit the original Display Module and/or Motor Control Module.

Suspension damper rods need replacing at the same time as bands.

Wash lint givers (eg. towels, flannelette sheets) separately from lint collectors (eg. synthetic fabrics). Over loading SmartDrive can increase the likelihood of linting. Insufficient detergent for the load can increase linting as there will not be enough detergent to hold the lint in suspension. Over drying synthetic fabrics in a dryer can cause a build-up of static electricity and result in the fabrics attracting lint.

remove bowl and clean them both

AquaSmart Error codes

Hi your shaft may be bent,Or metal particles on the rotor magnets.Get someone to turn the bowl & you look at the shaft without the rotor on & see if it's bent.

It's a motherboard power supply issue.Is your board part number IW SD11 420093These boards have that problem. let me know.

This is for an led screen

49. (00110001) Cold Valve or Cold Valve & Hot Valve Faulty The Motor Control Module has measured a voltage from the valve diagnostic circuit that indicates the cold valve or both the cold and hot valve is faulty. The most likely cause is that the valve harness has not been connected correctly or the valve(s) is open circuit. Primary Source: Wiring. Action: Check the valve harnesses are correctly fastened to the valves and the motor control module or the pins are not bent backwards. Secondary Source: Water Valves. Action: Measure the resistance of the cold and hot valve coils. Tertiary Source: Motor Control module. Action: Replace the Motor Control module.

Here is info on 248 fault code. 248. (11111000) SmartPump Top Up Fault More than 6 attempts have been made to top-up the water level in the bowl during recirc. This then signifies that the flapper valve has not closed full and some water is diverting to drain. Primary Source: Poor Flapper Seal. Action: 1) Clean any foreign objects out of the pump, concentrating especially on the flapper and drain/recirc port areas. 2) Remove the flapper to ensure no foreign objects exists below and around the flapper. 3) Check for flapper damage, especially the lip seals. If damaged, replace. Secondary Source: Cap not tight, warped, damaged (worn). Action: 1) Check that the hood/cap are tight. If loose and screws are difficult to tighten, foreign objects could be in screw boss. Remove pump fully and inspect/replace if in doubt. 2) Check the cap is not warped or it is not excessively worn in the area where it contacts the flapper. Replace the cap if warped or worn. Tertiary Source: Damaged Pump Housing Port Action: Check there is no excessive wear to the pump housing port caused by foreign objects. Replace pump if necessary. Quaternary Source: Motor Control Module. Action: Replace Motor Control Module.

The noise could be the load out of balance or Suspension damper rods & nect ring bands are worn & need replacing.

247. (11110111) SmartPump Flapper Fault The Motor Control Module has registered a drop in the water level during the recirculation phase of the wash cycle. Water is being drained instead of recirculated. The most likely cause is that the flapper is stuck in the drain position. Primary Source: Flapper valve. Action: Check for free movement of the flapper (replace if broken or damaged).

Fault code 40 info 40. (00101000) Bowl Dis-engage Fault While carrying out a bowl check, the Motor Control Module has found that the bowl is not engaged even though the pressure sensor indicates that the bowl is empty. The Motor Control Module continues to check for 2 minutes, after which time it displays this fault. The first two areas to check are the clutch and the pressure tube. If these two appear correct, then the fault could be in the pressure sensor in the Motor Control Module. Primary Source: Mechanical. Action: 1) Check that there are no clothes or other foreign objects preventing the clutch from re-engaging. Excessive suds can stop the bowl rotating. 2) If the machine is empty of water, carry out a clutch disassembly procedure and check the spline drive. 3) Next check that the pressure tube has not come off and that it is not kinked. Secondary Source: Motor Control Module. Action: Replace Motor Control Module.

The 1.6 Amp fuse is blown in the motor controller.