Top 20 Fisher and Paykel Aquasmart wl80t65c Questions & Answers


Fault code 49 is water valves - usually, the stop working when the rubber diaphagm inside gets hard, so a resistance only test is not conclusive (only tells us the solenoid is OK).
- Do a cold fill and a hot fill (briefly) to check for strong water flow on both.
- Regarding code 245, does water pump out strongly?
- One more thought, because these codes are both related to the water level in the machine, remove the level sensor hose at the controller end and blow into it to clear any blockage.

Fisher and... | 165 views | 0 helpful votes


Yes the shop you bought it from. At only 12 months old the warranty should still apply.

Fisher and... | 188 views | 0 helpful votes


Switch to Powdered Detergent and you wont have to clean your washer. Liquids leave a smelly, corrosive residue on the inside of the machine, use only Powder and leave the lid up when not in use to defeat the slime!

Fisher and... | 414 views | 0 helpful votes


Inside the drain pump. You can get to it by removing the spin bowl. Remove the 2 screws holding the pump cover & lift the cover off to expose the flapper valve.

Fisher and... | 146 views | 0 helpful votes


put powder down inside agitator not do not sprinkle over clothes not remove top off agitator first

Fisher and... | 68 views | 0 helpful votes


Replace just the lid lock assembly to start with and see how it goes. Lids are quite expensive and don't usually need replacing. You can always get a lid later if you still have problems.

Fisher and... | 177 views | 0 helpful votes


javascript:;To size set a L.C.D AquaSmartâ„¢ machine:
1. Press and hold the left
SCROLL
button, then press the
HIGH EFFICIENCY
button until two
beeps are heard.
2. Press the
SCROLL
button to select the machine size (600 for WL70, 650 for WL80).
3. Press the
POWER
button

Fisher and... | 184 views | 1 helpful votes


Your AquaSmart machine requires 4 new suspension damper rods & 4 top bands, these are a common problem for AquaSmart machines.

Fisher and... | 538 views | 0 helpful votes


Have you run a "Clean Up" cycle - it is important to do this to ensure your clothes are clean and the machine works at it's peak. If you use it heavily, you should do this every three or four months. You can find this cycle under "Lifestyle" and you should put 1 cup of oxyaction soaker in at the beginning of the cycle and it needs hot water to work. It takes about 3 hours, but is well worth the time.

There is no other real reason for a smell, unless something has died - in which case you should move the machine and remove any deceased animal.

Fisher and... | 118 views | 0 helpful votes


these are a common problem for AquaSmart machines.
Your AquaSmart machine requires 4 new suspension damper rods & 4 top bands,

Fisher and... | 186 views | 0 helpful votes


Did you look up your manual to help with the problem?

AquaSmart2 8kg - this is a link to download your manual

The good thing is that if you got Fisher & Paykel to come out, they offer a warranty on their service - so call them again and tell them the situation - they should come out for free....

Fisher and... | 226 views | 0 helpful votes


Hi! Have you completed a "Clean Up" cycle? It should prompt you every 100 washes to do a clean up - it should be under the "Lifestyle" menu. When you do it, I suggest you use OXY soaker (1 whole Cup) instead of normal detergent and make sure it is all HOT water. It soaks for 4 hours, but is very good at cleaning the bowl and workings to stop brown marks on your clothes and towels

Fisher and... | 89 views | 0 helpful votes


If you wish to get some details; check the site linked here. Pull up older posts. Surf the site with patience. http://electronicshelponline.blogspot.com/

Fisher and... | 216 views | 0 helpful votes


The LCD may have failed but also it could be failure of the display controller.

Fisher and... | 208 views | 0 helpful votes


Hi there..... mine did the same a couple of months ago, kept towels around, monitored, seemed to stop after some days (uses); Any update on yours ? Self-healed, Repairman, or Replaced ?

Fisher and... | 295 views | 0 helpful votes


this is all one unit hot and cold together sealed unit

Fisher and... | 167 views | 0 helpful votes


The most common problem with AquaSmart is the pump.
The pump has gone bad and blown the motor controller board.
Some AquaSmart machines display the wrong Error code (49)
witch is not the correct code for this problem.
Pump and motor controller board need replacing.
Maybe cheaper to buy a good secondhand machine.

Fisher and... | 217 views | 1 helpful votes


This model has a sensor, so the water comes on and off till it senses the right amount. If it is in water saving mode, then there will be no sitting water..... maybe you can give more details of the problem. Good Luck!

Fisher and... | 57 views | 0 helpful votes

Not finding what you are looking for?
Fisher and Paykel Aquasmart wl80t65c Logo

121 questions posted

Ask a Question

Usually answered in minutes!

Top Fisher and Paykel Washing Machines Experts

Archie Ferrarini
Archie Ferrarini

Level 3 Expert

869 Answers

Gerry Harvey
Gerry Harvey

Level 3 Expert

1481 Answers

jimorris77

Level 3 Expert

411 Answers

Are you a Fisher and Paykel Washing Machine Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

View Most Popular

Fisher and Paykel Washing Machines

  • Fisher and Paykel Washing Machines

Most Popular Question

fisher paykel top loading washing

  • Washing Machines
Loading...