Top 20
Fisher and Paykel Aquasmart wl80t65c - Page 9 Questions & Answers
Fisher and Paykel iw812 had
If it had code 37 why did you keep running it? Error codes are there for a reason. There may be no power because the pump is burnt out. Replacing the pump may restore the power if you are lucky. If power still does not come on after changing the drain pump then you are probably looking at a new control board as well. Your best thing to do is call a service company who will have a spare pump that they can try. If you buy a pump and then find it too expensive to buy the board as well, you will have wasted the money on the pump.
12/1/2017 2:18:04 AM •
Fisher and...
•
663 views • 0 helpful votes
I have a Paykel & Fischer washer, Model GWL10U2.
You need to understand that we can't see what you can. When you say it stopped, does that mean there is still power on & lights showing but it won't start or is there no power at all. Big difference in the way each will be fixed. If no power lights at all then you will need to call a service company as the main control board will have died.
11/17/2017 4:39:03 PM •
Fisher and...
•
194 views • 0 helpful votes
Fisher and Paykel washer fault code 40. Is it possible to repair DIY. What to look for?
This is error code 40.
40. (00101000) Basket Dis-engage Fault
While carrying out a basket check, the Motor Control Module has found that the basket is
not engaged even though the pressure sensor indicates that the basket is empty. The
Motor Control Module continues to check for 2 minutes, after which time it displays this
fault. The first two areas to check are the clutch and the pressure tube. If these two
appear correct, then the fault could be in the pressure sensor in the Motor Control Module.
Primary Source: Mechanical.
Action: 1) Check that there are no clothes or other foreign objects preventing
the clutch from re-engaging. Excessive suds can stop the basket
rotating.
2) If the machine is empty of water, carry out a clutch disassembly
procedure and check the spline drive.
3) Next check that the pressure tube has not come off and that it is
not kinked.
Secondary Source: Motor Control Module.
Action: Replace Motor Control Module.
5/21/2017 2:37:28 PM •
Fisher and...
•
4,949 views • 0 helpful votes
My fisher and paykel 5.5kg smart drive MW51
Possibly a worn RPS, they can be sensitive to moisture. so some days they can work fine, and other days can cause the motor to stall. normally gives a fault code though (which is why I have a suspicion this fault may be in the board). if you feel like leaning the machine on it's front (emptied, disconnected of course) you could look at the motor RPS on the rear of the motor. see if it shows signs of corrosion. you will need to remove the rotor (spinning bit) to see the RPS. *(follow the wires to the RPS)
9/8/2017 6:21:03 PM •
Fisher and...
•
210 views • 0 helpful votes
Screeching noise during operation of machine
If it only screeches when the drain pump is running you can spray some crc or wd40 in to the bearing on the drain pump. That usually helps. You will have to turn power off at wall, tip machine back against a wall and get at the pump underneath on the right side at the front.
6/24/2017 5:42:03 PM •
Fisher and...
•
934 views • 0 helpful votes
I have a Fisher Paykel
Fault code 49 is saying that the control board is getting an incorrect reading from the cold water inlet valve circuit. Can be a faulty inlet valve, bad connection on the wiring or more common is that the control board has a fault and will need to be replaced.
9/30/2017 5:45:03 PM •
Fisher and...
•
59 views • 0 helpful votes
Why is lid not locking?
Replace the lid lock. If you post a model number I can give you a part number. Over time lid locks sometimes wear out over time( most of them are 90% plastic). Lid locks should be relatively inexpensive. Also if this is a top load washer you can replace it yourself instead of hiring someone.
8/13/2017 10:18:03 PM •
Fisher and...
•
187 views • 0 helpful votes
Not finding what you are looking for?