Top 20
Fisher and Paykel Aquasmart wl80t65c - Page 2 Questions & Answers
My WL80T65CWI does not get water
This model has a sensor, so the water comes on and off till it senses the right amount. If it is in water saving mode, then there will be no sitting water..... maybe you can give more details of the problem. Good Luck!
6/11/2014 3:12:38 AM •
Fisher and...
•
68 views • 0 helpful votes
FISHER PAYKEL FAULT CODE 9
if its a top loader that is incorrect it mean machine needs resizing and if tht doesnt work a new main control module
1/3/2014 12:22:44 AM •
Fisher and...
•
590 views • 0 helpful votes
Error 27 Fisher and Paykel
27. (00011011) Fabric Softener Valve Fault
The Motor Control Module has measured a voltage from the valve diagnostic circuit that
indicates the fabric softener valve (with Yellow Clip) is faulty. The most likely cause is that
the valve harness has not been connected correctly or the valve is open circuit. See fault
code 49 for service procedure.
12/30/2013 4:41:40 AM •
Fisher and...
•
638 views • 0 helpful votes
Is there a filter in the machine that \i should be cleaning as i keep getting black bits on the clothes?
The black bits are scum flaking off from between the inner & outer bowls, usually more common with cold water wash. Place old towel in washer, fill washer to high level with hot water, add washing soda & or vinegar, let washer run to end of wash cycle, turn off & let it soak for around an hour, turn back on & let it go through cycle. Commercial washing machine cleaning products should also be availably in your supermarket / hardware stores. You may need to repeat process until no more gunk comes out.
12/21/2013 12:23:18 AM •
Fisher and...
•
677 views • 0 helpful votes
How to clean machine
what are you wanting to clean?? most places are the pump & bowl under the agitator..
the pump is under the machine, some have a little plastic side hatch you open to get to the pump.
the bow is gotten to but removing the agitator, usually a thumb nut down the middle of agitator, and then pull up agitator to remove out the top,
soak up all the water & clean out the dirt & scale you find.
2/20/2014 12:25:24 AM •
Fisher and...
•
101 views • 0 helpful votes
Fisher Paykal error 49
In the AquaSmart machines the pump over currents and blows the water valves fuse 1.6 Amp glass, The motor controller board
would be faulty as well and need repair.
49. (00110001) Cold Valve or Cold Valve & Hot Valve Faulty
The Motor Control Module has measured a voltage from the valve diagnostic circuit that
indicates the cold valve or both the cold and hot valve is faulty. The most likely cause is
that the valve harness has not been connected correctly or the valve(s) is open circuit.
Primary Source: Wiring.
Action: Check the valve harnesses are correctly fastened to the valves and
the motor control module or the pins are not bent backwards.
Secondary Source: Water Valves.
Action: Measure the resistance of the cold and hot valve coils.
Tertiary Source: Motor Control module.
Action: Replace the Motor Control module.
1/5/2014 2:59:45 AM •
Fisher and...
•
289 views • 0 helpful votes
Machine is leaking from underneath
Have you taken the lid off and looked at the operation whilst going through the self cleaning cycle? Have you checked that the hoses, i.e. clips, are secure? Have you checked for cracking in the hoses? If it is not evident have you tried tying kitchen towel round hoses? Have you cleaned the filter out?
11/18/2013 2:26:44 AM •
Fisher and...
•
233 views • 0 helpful votes
Error code 49 wl80t65c
cold water valve fault. often caused by the motor controller failing. test valve during fill for 24V recieved. if not, motor controller needs replacing.
8/30/2013 10:51:31 AM •
Fisher and...
•
224 views • 0 helpful votes
Error code 50
50.(00110010) Hot Valve Coil Faulty
The Motor Control Module has measured a voltage from the valve diagnostic circuit that indicates the hot valve is faulty. The most likely cause is that the valve harness has not
been connected correctly or the valve is open circuit. See fault 48 for service procedure.
48. (00110000) Hot and Cold Valve Coil Faulty
The Motor Controller module has measured voltages from the valve diagnostic circuit that
indicate both the hot and cold valves are faulty. The most likely cause is that the valve harnesses have not been connected correctly or the valve is open circuit.
Primary Source: Wiring.
Action: Check the valve harnesses are correctly fastened to the valves or the
pins are not bent backwards.
Secondary Source: Water Valves.
Action: Check the valve coils are not faulty (open circuit).
Tertiary Source: Motor Controller module.
Action: Replace the Motor Controller module.
8/9/2013 3:23:54 AM •
Fisher and...
•
404 views • 0 helpful votes
Need a service, fault 49 ???????
cold valve fault. check the water supply, check the valves. otherwise it's the motor controller. replace parts as necessary.
8/28/2013 10:25:38 PM •
Fisher and...
•
169 views • 0 helpful votes
My Fisher and Paykel Aquasmart is leaving white marks on my clothes. I am using the correct washing liquid, so how can I fix this? I am sick of re-washing half of my clothes
WASH PERFORMANCE INFORMATION
12.1 Creasing
Creasing can be caused by over loading SmartDrive or the dryer. Permanent Press or Delicate
cycles have been designed to minimise creasing as they use a lower spin speed. Do not leave wet
clothes to sit in the washer or laundry basket.
12.2 Soiling
Soiling is the result of insufficient detergent for the load. White clothes are better washed
separately. Separate lightly and heavily soiled items, as clothes can pick up soil from dirty wash
water. Cold water below 20oC does not wash effectively. Select the wash temperature according
to soil type. For example, blood and mud are better washed in cold water, while sweat and oil
based soil wash better in warmer water. Loads made up of articles of varying sizes will wash
better (e.g. full loads of sheets may not wash that well). Hard water requires more detergent than
soft water.
12.3 Linting
Wash lint givers (eg. towels, flannelette sheets) separately from lint collectors (eg. synthetic
fabrics). Over loading SmartDrive can increase the likelihood of linting. Insufficient detergent for
the load can increase linting as there will not be enough detergent to hold the lint in suspension.
Over drying synthetic fabrics in a dryer can cause a build-up of static electricity and result in the
fabrics attracting lint.
12.4 Detergent Residue
Over loading SmartDrive can result in detergent residue being caught in the creases of the
fabrics. If this occurs, decrease the load size. Some detergents need to be pre-dissolved. Check
the instructions for the detergent. Cold ambient temperatures, cold washes or short agitation times
may not let the detergent dissolve properly. In these cases pre-dissolve the detergent.
Overdosing of detergent can also cause residue when foam breaks down and will show as white
specs on the clothing. Poor quality detergents can result in residue.
12.5 Black Marks on Clothes
A build up caused by the interaction of fabric softener and detergent (scrud) can flake off and mark
clothes. Do not use too much fabric softener, maximum 75cc. If this is a problem, it is
recommended that SmartDrive is periodically filled with hot water, plus 1-2 cups of dishwasher
powder and left to soak.
12.6 Grey Marks on Clothes
Not enough detergent for the amount of soil on the clothes can result in grey marks on clothes. If
this is a problem it is recommended that SmartDrive is periodically filled with hot water, plus
detergent and left to soak.
12.7 Dye Transfer
Wash and dry non-colourfast clothes separately. Non colourfast clothes left sitting in a washer or
laundry basket can transfer dye to other clothes.
12.8 Tangling
Washing with too much water (i.e. under loading) can cause the clothes to tangle around each
other. Do not load SmartDrive by wrapping clothes around the agitator.
5/24/2013 1:41:14 AM •
Fisher and...
•
820 views • 0 helpful votes
Not finding what you are looking for?