20 Most Recent
RCA Scenium D40W20 40" Rear Projection HDTV - Page 4 Questions & Answers
Have sound no pic. on 52 inch.
if you have some thin lines on the top of the picture probably you have a problem on the power supply for the convergence
How to enter service mode to resize grid.
Many a good set have been destroyed by stumbling around in the service menu. One wrong thing and boom no more Tv. But we'll try to help you here, turn the set off. hold both the volume down and chanel down on the front of the set. hold them both in till the set turns on Then from this menu go to geomatry and you should be able to adjust from there , and for Gods sakes write down the values before you change them so you have a refrance point should things go terribly wrong
RCA Scenium
What does the picture look like when it is on?
Need to replace Flyback Transformer
FBT just solders in and out you do not have to have sams which now comes on disk to replace Fly.You need part # to FBT there is only 2 wires to hook back up .
Rca d40 w20 lost component "spark gap"
Yes they are spark gaps and no when bad high voltage will arch out of them, Go to Cp150 2200uf 16 capacitor if it is puffed up on top it is bad .you have 3 that need re[lacing cp114 cp120 cp150
GE D40GW10 turns off after a minute
Yes and No it depends on what is wrong If your luky it will be 3 capacitors on Deflection board cp150 2200uf 16v and cp114 cp120 220uf 35v capacitors they are green with gold writing on them If cp150 is puffed up on top it is bad. So then replace other 2 caps.
The rca scenium / src
you need to replace the bulb. It costs about a hundered dollars and you can replace it yourself. refer to the lamp replacement instructions that came with your set
Rca d40w20 tv convergence and power on problems
The problem is most likely due to a defective convergence IC.
There are two convergence STK ICs located on the convergence board.
You need first to test the ICS, by checking for continuity the pico fuses at the base of the ICs, then replace the faulty STK.
You should trying doing it yourself only if you are a proven electronic repairer.
RCA 42in Projection
There is a short, the tv is trying to come on but the fault is keeping it from coming on. Try to find a bad board inside the tv, check all fuses or continuity. Thatll give you a place to start from.
Problem with TV
One of the boards may have failed, have you looked inside the tv?
Rear input connectors
Does it give you a "No Signal" on the screen, you may have to check the xbox and make sure you have it setup to output a HD signal. Let me knwo what you find.
TV NOT WORKING
There must be a bad board somewhere, sounds to me like a board has shorted and it has gone into a self protection mode. Start at the power supply and remove connections, if you can check and make sure that you are getting the correct voltages out of the power supply, look for anything that may be blown or blackened, specifically fuses. Let me knwo what u find.
No sound
you can't, you have to use the rca jacks for the audio they should be by the DVI connector.
My rca model d40w20 b
the power supply finaly quit, it need service, problably the "doubler" circuit is out.
RCA HDTV D40W20: Turning it ON
There seems to be problem withe picture screen.Drop into the nearest service center and it will be fixed.Its not a problem at all..
To find the nearest service center in your area click on the link below..
http://direct.where2getit.com/cwc/apps/w2gi.php?client=rcathomson&template=searchretail_new
I turn my tv on and there is no picture, but i do have sound
then your tv will need repair , as a video processing circut has failed , this is happening alot to these tv's
you will need to call a local repair shop to have a tech come out and test it to determine the cause
sorry about your tv
electech
Not finding what you are looking for?