20 Most Recent RCA D52W20 52" Rear Projection HDTV-Ready Television Questions & Answers

it could indicate that the TV is in standby mode, waiting to be turned on. In this case, you should be able to turn on the TV by pressing the power button on the remote or on the TV itself. If the red light stays on even after attempting to turn on the TV, it could indicate a problem with the TV's power supply or circuitry. In this case, it's best to consult the TV's manual or contact LG customer support for assistance. Regarding the RCA D52W20 52" Rear Projection HDTV-Ready Television, if you're experiencing issues with this TV, it's best to provide more information about the specific problem you're encountering, such as error messages, distorted picture or sound, or issues with turning on or off. This information will help diagnose the problem and provide more targeted solutions.

what cuircit are you searching for power defelection, sub power, convegence power convegence amp, crt boards, signal board

The swollen electrolytic cap dose indicate defect but, also may mean a run-away voltage from an open zener diode or shorted regulator which regulates voltage. With luck, replacing the cap may do it, but may not complete the needed remedy. If you are not proficient with soldering or PC board work, I would strongly suggest taking unit to qualified service for complete analysis and repair

Yes you can get screen assemblies from www.tvrepairworld.com send them a email if you only need the outer panel as thats a three panel screen system.

I see this a lot at the shop. the front panel buttons have become damaged. The best coarse of action is to replace the front button circuit board assembly... **** there is a temporary fix until you get the part... remove the front panel and take button circuit board out...just use remote to control the tv. This is also a way to test to see if this is the problem.. if you remove the connector to the buttons and the problem goes away then the buttons are the problem. you get get this circuit board at union electronics. You have to get the extended model number off the back usually d52w20yx1 or yx2 or yx something...not to difficult a repair

Sounds like your power board has issues and needs repairing or replacing, if your tech savvy you can repair it but it might make more sense to order a new one, this board is known for issues in tvs like you have

I have a RCA big screen TV and it has a beeping sound when I plug it up and try to turn it on

Hello bowmaster30,

I can send you a copy of the schematic, Radio shack has these capacitors, also www.electronix.com has them. In fact any electronics parts store would have them. Let me know if you still need the schematic.

Thank you,

Shuttle83,

http://www.electron-age-technologies-llc.com

sounds like dust collected on the internal parts which after enough time can cause it to stop working. either have tv repair specialists replace the mother board, or replace tv

how long? 3 seconds.. does it sound like chirping? is it comeing from back. smell anthing?

• Debra try this to reset, do not use remote for this operation.
• With the TV powered on complete the following steps:
• Press and hold "Menu" button on the front of the TV
• Press and release the "Power" button on the front of the TV.
• Press and release the "Volume Down" button on the front of the TV.
• This should bring up the service menu.
• Using the buttons on the front of the TV, scroll down and select (Reset to Factory Defaults).

Check the attached links,instruction and guides, Good luck "I hope this helped you out, if so let me know by pressing the helpful button. Check out some of my other posts if you need more tips and info." Are You locked Out Questions Answers for RCA reset to factory settings Projection Televisions RCA D52W23 Troubleshooting Manual

Yes - it needs the special tuner to receive digital transmissions.

if it is the chassis im think it is you will have to take the back off looking at the chassis the very front right corner there is a board apporx. 6in. long 2,3 in wide look at the fuse if it's blown take the small board out make sure set is unplugged it just clips in around the edges with plastic clips there are a set of diodes toward the opposite end they make check shorted if so replace there is a part number on the side of the diodes call some shops or go to fry's online maybe







if it is not blown there are 2 wire cable that comes from that board all the way up to another board called the deflection but the easiest way to check it is your board at eye level to the right those wires go there also a brown and green or blue wire to the top left hand corner of that board check with a volt meter on D/C setting for 300 to 340 volts if you have those volteges you could have a problem on the deflection board

Just fixed it!!! Remove the back panel from the television, you will see a board where the input jacks are located. To the left you will notice a red power wire. Just up and to the right approx 7" or so you will see a [_] shaped metal shield surrounding a capacitor in the middle of it. The part # on the board is CP150. It is a green/gold 16v 2200uF capacitor. More than likely this capacitor is faulty. Run your finger over the top of the capacitor, if it is beveled rather than smooth you have a definite solution to your problem. You may need to remove the plastic piece that covers the transformer to the left of the capacitor to gain easy access. Good luck!!

bad color wheel

Power supply failure. Now a boat anchor.