Podtermistor wa?ka utrwalaj?cego nie
wykrywa wymaganej temperatury w ci?gu 30 sekund.
po rozpocz?ciu cyklu rozgrzewania; dlatego
kopiarka nie ko?czy cyklu nagrzewania.
• Temperatura wa?k?w utrwalaj?cych nie
osi?ga wymaganego poziomu nawet po
up?ywie ustawionego czasu podczas cyklu nagrzewania.
1
Sprawd?, czy lampka utrwalacza H1 zapala si?, gdy g??wny
wy??cznik zasilania jest ustawiony w pozycji W?., w razie potrzeby popraw lub wymie?.
- -
2
Sprawd?, czy H2 w??cza si?, gdy g??wny
wy??cznik zasilania jest ustawiony w pozycji ON, i w razie potrzeby popraw lub wymie?.
- -
3
Sprawd? instalacj? TH1 i TH2 i
w razie potrzeby popraw lub wyczy??.
- -
4
Sprawd? dzia?anie TH1.
Usu? CN80 (4P), a nast?pnie sprawd?, czy rezystancja
na CN80-2 i -3 na termistorze jest
niesko?czona.
- -
5
Sprawd? dzia?anie TH2.
Usu? CN81 (4P), a nast?pnie sprawd?, czy rezystancja
mi?dzy CN81-2 i -3 na termistorze jest
niesko?czona.
- -
6
Sprawd? ci?g?o?? H1.
W razie potrzeby popraw lub wymie?.
- -
7
Sprawd? ci?g?o?? H2.
W razie potrzeby popraw lub wymie?.
- -
8 Zmie? PU1 - -
9 Zmie? PWB-A
Printcopy.infohttps://printcopy.info > model=Di2510
Code: C0045 · Description: Cooling Fan Failure The Cooling Fan Motor Lock signal remains set to H for a set period of time while the Cooling Fan Motor is ...
What is error code c2557 on Konica c220?
Check the toner bottle to ensure that it is feeding toner into the sub hopper unit under the bottle. Sometimes users will insert the bottle incorrectly and not lock it properly in place...the lever on the front of the toner hopper for that bottle is moved down to the left to remove and insert the bottle.
Dec 28, 2010
All in the link. You can't Scan FROM a USB drive because if it was on the USB Drive it is already in digital format. You can Scan TO a USB Drive.
For the faint text, remove the toner cartridge and give it a couple of hard taps on the either end to settle the toner. Then run a Test Page
https://www.google.com/search?q=Minolta+Bizhub+220+scan+or+print+from+flash+drive
..
Printcopy.infohttps://printcopy.info > code=C-2402
Code: C-2402; Description: Erase lamp (EL) connector slip-off abnormality. - When EL turns ON before starting an initial charging, EL abnormality has been ...
Missing: press C6000 Pro.
You can try it, but the manual says 10 at a time via the Bypass tray. The problem is the fact that normal paper from the trays takes a rather tortuous route through the machine that contains sharp turns. By far the easiest way to print a lot of envelopes is to use Avery 8163 Labels. Use the Avery template and create the pages of addresses and print 50 at a time from the normal paper tray.
https://www.google.com/search?q=Konica+Minolta+Bizhub+880+print+9+x+12+envelopes
Question edited to add English make and model.
Question moved from Cars and Trucks category.
English only on Fixya please. We are a North American website.
Reset maintenance minolta dialta di152.
Cruet of oil.
And this is the problem. Copiers have a 'cruet of oil'? And they do!
https://www.google.com/search?q=minolta+dialta+di152+oil+tank
..
If you have already replaced the charging corona, developer powder, and cleaned the laser unit, but the problem of a white light appearing on the artwork persists on your Konica Minolta Bizhub C454, here are a few additional steps you can take:
Check the transfer belt unit: Ensure that the transfer belt unit is clean and free from any debris or toner particles. You can gently wipe it with a clean, lint-free cloth. If the transfer belt is damaged or worn out, it may need to be replaced.
Inspect the imaging unit: Check the imaging unit (drum unit) for any signs of damage or wear. Make sure it is properly installed and securely seated in its designated position. If the imaging unit is defective, replacing it might resolve the issue.
Perform a density adjustment: The Bizhub C454 usually has a density adjustment function. You can access this in the device's settings menu or through the control panel. Performing a density adjustment might help improve the print quality and reduce any unwanted artifacts.
Check the print settings: Ensure that the print settings on your computer or the printer's control panel are appropriate for the artwork you are printing. Adjust the print quality, resolution, and any color settings as needed.
Update the firmware: Visit the Konica Minolta website and check if there are any firmware updates available for your Bizhub C454. Updating the firmware can sometimes address software-related issues that may be causing the white light problem.
If none of these steps resolve the issue, it is recommended to contact Konica Minolta's customer support or a certified technician for further assistance. They will have specialized knowledge and tools to diagnose and fix the specific problem with your machine.
There are several reasons why your Konica Minolta C250i printer may be printing magenta as yellow. Here are some troubleshooting steps you can try:
Check the magenta toner cartridge: Make sure that the magenta toner cartridge is properly installed and has enough toner. If the toner cartridge is low or empty, replace it with a new one.
Clean the printer heads: Use the printer's cleaning function to clean the printer heads. This can help remove any clogs or buildup that may be preventing the magenta ink from flowing properly.
Check the printer settings: Check the printer settings to make sure that the correct paper type and color settings are selected. If the printer is set to print in grayscale or black and white mode, it may not use the magenta ink.
Perform a firmware update: Make sure that your printer has the latest firmware installed. Sometimes firmware updates can fix issues with printing quality.
Contact Konica Minolta support: If none of the above steps solve the issue, you may need to contact Konica Minolta support for further assistance. They may be able to diagnose the issue remotely or send a technician to your location.
The pickup rollers at the bypass tray may be dirty with paper dust and have lost their grippyness. Try cleaning them with a lint free cloth with a drop of washing up liquid. Wipe with a damp cloth and leave them to dry. Sometimes with age they can look perished and crack in which case or replace them if necessary.
Also the Bypass Tray has a little switch which tells the machine it is feeding from there. Make sure it is moving.
