I JUST NEED ORDER NUMBERS FOR ALL THE COLOR LASERJET CARTRIDGES FOR CP4525 PLS. THANKS,

Hi,

you might need to update the fuser assembly. Please ensure that there are no other issues (ie paper jam or low toner level) before restarting your printer. Otherwise, please ensure that your printer isn't overheating. If so, turn it off for 30 minutes before using again.

Thank you.

try this link might help you out... HP color laserjet enterprise cp4525 display error 49 2FA7 Google Search

A 50.2 fuser error will on most cases require replacement of the fuser assembly. It is located on the right hand side of the printer. Same side as the manual feed tray. Open the door and look for two blue handles near the top of the opening.

Disconnect all usb and network cables and cycle the power. If the printer comes to ready then chances are you do not have a "hardware issue". Most common cause of 49 errors is out of date firmware. If you search the tips I have posted there is a detailed one on how to upgrade firmware.

Replacing the Transfer Belt (ITB, Transfer Kit) HP Color LaserJet CP4525 CM4530
1. Open the printer's right side door.
2. Use the blue lever (see callout 1 in picture below) to lower the secondary transfer assembly.
3. Grasp the small handles on the transfer belt assembly (circled in blue in picture below), and begin gently pulling the assembly out towards you, until a set of 2 larger handles pop free on the sides of the transfer belt assembly.
4. Now grasp the larger handles on the transfer belt assembly, and continue pulling the transfer belt straight out of the printer until it is completely removed.
5. Avoid touching the surface of the new transfer belt. Install in reverse order, sliding it securely into the machine.
6. After replacing the Transfer Belt, it's a good idea to perform a Full Calibration (or even several Full Calibrations in a row, if you are having print quality issues). Full Calibrations help with print quality by aligning the color tones, the drums, and the color plane. Each Full Calibration takes about 4 minutes. To perform a Full Calibration: Press MENU to enter the menus. Press Down Arrow to highlight CONFIGURE DEVICE. Press Checkmark to select CONFIGURE DEVICE. Press Down Arrow to highlight PRINT QUALITY. Press Checkmark to select PRINT QUALITY. Press Down Arrow to highlight FULL CALIBRATE NOW. Press Checkmark to select FULL CALIBRATE NOW. Wait for the printer to calibrate (usually takes 4 minutes or so), and then print a test page. If print quality still needs improvement, repeat the Calibration. If multiple Calibrations don't help, some of the toner cartridges may need replacement.

http://www.printertechs.com/other-instructions/104-replacing-transfer-belts-itb-transfer-kit-hp-color-laserjet-printers/397-changing-the-hp-color-laserjet-cp4525-cm4540-intermediate-transfer-belt

Hi
probably this fuser unit is faulty, the other issue this machine uses the electric current 110 v or 220v

Try another cyan toner cartridge. Let me know what happens. Print Quality Troubleshooting Tool for HP Color LaserJet CP4025 CP4525

Unfortunately laser printers don't work this way. The laserjet 1022 was designed for black and white prints only. In order to do color printing with a laser printer you will need to purchase one that is designed to print in color. The laser printers work a bit differently than the inkjets - the laser printers have 4 toner cartridges, one each for Cyan, Magenta, Yellow, and Black, that work together to print a full color page. With the old inkjets you could just replace a black cartridge with a color one.

So, short answer: Sorry but no you can't make a laserjet 1022 print in color. :)

I would recommend looking at an entry level color laser printer from hp, such as the CP2025 (http://h10010.www1.hp.com/wwpc/us/en/sm/WF25a/18972-18972-3328060-15077-236268-3673580.html) if you are looking into purchasing a color laserjet.

Hope this helps

Please rate this post, thanks!

Its a 3 step process follow it it will fix your issue

1. Turn the printer off, and then turn the printer on.
2. Check and reseat the fuser and toner cartridge to make sure they are not hindering gear movement in the drive train.
3. Check the main motor's cable to ensure that it is seated properly. 4. If the error persists, replace the main motor.