How do I pull out tray behind toe grille to clean?

You should have a copy of it behind the toe grille on the front. Or on the back of the unit.

Good Morning Jill,

I see that you are trying to remove the doors on your Frigidaire refrigerator, model# FRS23R4A, for shipping purposes. Below are the instructions you will need to follow for both the refrigerator and freezer doors.


DOOR REMOVAL INSTRUCTIONS:
If it is necessary to move the refrigerator through narrow doorways, follow these steps to remove the doors.
IMPORTANT: Before you begin, turn your freezer and fresh food controls to "O" and remove electrical power cord from the wall outlet. Remove any food from the door shelves.

1. Disconnect electrical supply.
2. Open both doors, then remove toe grille.
3. Close doors.

To Remove Refrigerator Door:

1. Remove top hinge cover screw on refrigerator door and remove cover.
2. Trace around hinge with soft lead pencil. This will make it easier to realign doors when they are replaced.
3. Remove top hinge and lift refrigerator door off bottom hinge pin. Set door aside.
4. Remove bottom hinge, if necessary.
5. Reverse this procedure to reinstall refrigerator door.

To Remove Freezer Door:

1. Disconnect water line coming from lower hinge of freezer door at connection located under front of freezer: Press outer ring against face of fitting, then pull to remove tube.
2. Remove top hinge cover screw on freezer door and remove cover.
3. Disconnect wiring harness connector plug at top hinge: place your thumbs on flat sides of each connector and bend both parts back and forth, then with firm grasp, pull both pieces apart.
4. Trace around hinge with soft lead pencil. This will make it easier to realign doors when they are replaced.
5. Remove top hinge, allowing wiring harness to pull through hinge and lift freezer door off of bottom hinge pin. Lay door down flat to avoid kinking water line.
6. Remove bottom hinge, if necessary.
7. Reverse this procedure to reinstall freezer door.

When both doors have been reinstalled, connect water line by inserting tube and push until mark touches face of fitting, replace toe grille and plug in electrical power cord. Turn both temperature controls to center position. Adjust settings as necessary. Hope this is helpful.

-Best Regards-
WP

The drip tray is accessible from the rear of the Grill. It is necessary to lift up the pan slightly while pulling it out. Or depending on how old your VC grill is, it may be located on the left end of the grill (you should see a small handle). In which case you pull it out and was you reach the end of the drip tray, lift it up slightly to remove it.

TIP: To make clean up of the drip tray easier. Spread a thin layer of Speedy Dry (It's what NASCAR & garages use to soak up oil) on the bottom of the drip pan or tray. You can purchase a bag of it, at any auto parts store, When it comes time to clean the drip tray or pan. Just remove the tray or pan and dump the used Speedy Dry in the garbage. Then, spread a thin layer in it again. Actually, because the Speedy Dry absorbs so well, you'll find that you'll only have to dump the tray or pan occasionally.

Hope this helped you and Happy Grilling!!

Yes, usually the tray can be removed for cleaning. You will have to pull the fridge out, unplug power, remove the rear access cover. Then you should see the evaporator / condensate tray and how to remove it.

Usually the model number is on the leg behind your bottom pull-out drawer. If not there, then look where the oven door sets into the oven frame on both sides, or the very bottom where the door hinges. If you have an older unit that has a top that lifts up, then look under the top. Some brands hide their model number behind a oven vent or grill, shine your flashlight through the oven air grills and see if their is a model number plate behind the grill. Finally some units will have the model number removed by the factory if it was a unit returned under a lemon law. These are not supposed to be sold to the public, but we have seen them. In these cases the only way to get some parts is to pull the actual part and see if their is a part number on it. Good Luck, Appliance Specialists

it should be right inside the refer
open the door look up
it might be on the upper right
upper left
middle on the ceiling
yes on the cieling
if its an older one
pull off the toe kick
it will be on a plate on the unit behind the toe kick

The filter is behind the front grill. Pop off the grill, should just pop off, pull down from the top under the vents. the filter is behind there.

Insert a putty knife into the seam where it meets the front panel about 2 inches in from each side. There is a small retainer clip that you will need top depress in order for the panel to release. If you go to searspartsdirect.com and enter your model number, you can find a helpful illustration under the "Cabinet" heading. The clips I mention are listed as item 46 just ot give you a perspective. I would also strongly recommend that you UNPLUG the dryer before cleaning the interior cabinet. There are live voltages present even with the dryer turned off. Particulary around the heating circuits. I hope you find this information helpful.

First clean the condensor coil. it will either be under the fridge behind the toe grill or in the back of the machine behind the rear cover depending on the make and model of your fridge. You will also want to make sure the condensor fan is running. It will be located behind the cover at the back of the unit near the compressor. Post back with the complete model and serial numbers from the fridge if you need any more help.
Thanks, Mike