Prints every other line

On the pixma printer each time you remove a cartridge. you will need to do a clean of the nozles and print head. you can find instructions in your online operators manual. You hold down the wi-fi button and watch the
Home Click Here to Search
MG3500 series > Overview of the Machine > Maintenance > When Printing Becomes Faint or Colors Are Incorrect
When Printing Becomes Faint or Colors Are Incorrect

Maintenance Procedure
Printing the Nozzle Check Pattern
Examining the Nozzle Check Pattern
Cleaning the Print Head
Cleaning the Print Head Deeply
Aligning the Print Head
Page top
error light flash. 1 flash release prints all saturation levels2 flashes prints the head alignment chart. 3 cleaning 4 flashes deep clean and so on. or its a transfer problem and this case do a transfer belt clean, and a head alignment.

G to Canon U.S.A. : Support & Drivers : Consumer & Home Office.If more help needed post back.

Go to Control Panel. Click on Printers & Faxes. Right Click on your Printer's icon. Click Properties on the drop down menu. Click Maintenance Tab. Select Print head Alignment. Carry out the instructions displayed. A print test page will be printed after the alignment has been done. Check the printed matter with the sample page. If not OK again carry out the process till you get a clear printed page.

Most probably is PURGE UNIT not functioning well. If print out still acceptable then just ignore the ink stain.

Remove the black cartridge and soak it with an alcohol free window cleaner soaked paper towel let it sit on the towel for a good thirty minutes then wipe clean and put back in printer run nozzle check if necessary.

Here's the solution from Canon USA:

Issue: Banded or streaked prints
Solution: Print Head Alignment MP530

Perform Print Head Alignment Instructions to perform a Print Head Alignment directly from the machine. If diagrams or ruled lines are misaligned, print head alignment is required. The print head alignment can be performed automatically or manually. If the automatic print head alignment does not work, adjust the print head manually. Automatic Print Head Alignment

1. Press <ON/OFF> to turn on the machine.
   
   
2. Load a few sheets of letter-sized plain paper in the auto sheet feeder.
   
   
3. Press the Open button to open the Paper Output Tray. Then open up and set the extension by pressing down the hollow on the front side.
   
   
4. Execute automatic print head alignment.
   
5. 1. Press <COPY> button.
      
   2. Press <Menu> repeatedly to select [MAINTENACE].
      
   3. Press the left or right cursor to select [AUTO HEAD ALIGN], then press the <OK>. (A pattern is printed and the print head is automatically aligned. It takes about five minutes to finish printing the pattern.)
      
      
      
      

Manual print head alignment

1. Press <ON/OFF> to turn on the machine.
   
   
2. Load two sheets of Letter-sized plain paper in the auto sheet feeder or cassette.
   
   
3. Ensure that the proper paper source is selected.
   
   
4. Execute manual print head alignment.
   
5. 1. Press <Menu> repeatedly to select [MAINTENACE].
      
   2. Press the left or right cursor to select [ALIGN PRINT HEAD], then press the <OK>. (The nozzle check pattern is printed.)
      
      
6. Check the printed patterns and use the left or right arrow to input the number of the pattern in column A that has the least noticeable streaks.
   
   
   
   
7. Press <OK> to move the cursor to column B, and then use the left or right arrow to input the number of the pattern that has the least noticeable streaks.
   
   
8. Repeat the procedure until you finish inputting the pattern number for column P.
   
   
   
   
9. When you have finished inputting all pattern numbers, press <OK>.
   
   Note: For columns A through N select the patterns with the least visible vertical streaks. For columns O and P select the patterns with the fewest visible horizontal streaks.
   
   
   
   <1> Example of the pattern with the fewest visible vertical streak
   
   <2> Example of the pattern with the most visible vertical streak
   
   
   
   <1> Example of the pattern with the fewest visible horizontal streak
   
   <2> Example of the pattern with the most visible horizontal streak
   

Hope this helps - fotobean

Here's a solution from Canon USA:

Issue: Banded or streaked prints
Solution: Print Head Alignment MP530

Perform Print Head Alignment Instructions to perform a Print Head Alignment directly from the machine. If diagrams or ruled lines are misaligned, print head alignment is required. The print head alignment can be performed automatically or manually. If the automatic print head alignment does not work, adjust the print head manually. Automatic Print Head Alignment

1. Press <ON/OFF> to turn on the machine.
   
   
2. Load a few sheets of letter-sized plain paper in the auto sheet feeder.
   
   
3. Press the Open button to open the Paper Output Tray. Then open up and set the extension by pressing down the hollow on the front side.
   
   
4. Execute automatic print head alignment.
   
5. 1. Press <COPY> button.
      
   2. Press <Menu> repeatedly to select [MAINTENACE].
      
   3. Press the left or right cursor to select [AUTO HEAD ALIGN], then press the <OK>. (A pattern is printed and the print head is automatically aligned. It takes about five minutes to finish printing the pattern.)
      
      
      
      

Manual print head alignment

1. Press <ON/OFF> to turn on the machine.
   
   
2. Load two sheets of Letter-sized plain paper in the auto sheet feeder or cassette.
   
   
3. Ensure that the proper paper source is selected.
   
   
4. Execute manual print head alignment.
   
5. 1. Press <Menu> repeatedly to select [MAINTENACE].
      
   2. Press the left or right cursor to select [ALIGN PRINT HEAD], then press the <OK>. (The nozzle check pattern is printed.)
      
      
6. Check the printed patterns and use the left or right arrow to input the number of the pattern in column A that has the least noticeable streaks.
   
   
   
   
7. Press <OK> to move the cursor to column B, and then use the left or right arrow to input the number of the pattern that has the least noticeable streaks.
   
   
8. Repeat the procedure until you finish inputting the pattern number for column P.
   
   
   
   
9. When you have finished inputting all pattern numbers, press <OK>.
   
   Note: For columns A through N select the patterns with the least visible vertical streaks. For columns O and P select the patterns with the fewest visible horizontal streaks.
   
   
   
   <1> Example of the pattern with the fewest visible vertical streak
   
   <2> Example of the pattern with the most visible vertical streak
   
   
   
   <1> Example of the pattern with the fewest visible horizontal streak
   
   <2> Example of the pattern with the most visible horizontal streak
   

Hope this helps - fotobean.

try to print as T-Shirt transfer - the printer automatically mirrors the printout then

Head Align Failed

Your color profile is off

Click on start / printer and faxes

right click on your printer and select properties

click on the color management tabe and selct another color profile

If that dont work

in the printing preferences (propteries) adjust the amout of maganta(red) down a bit to compensate for the rest..

but the problem is your color profile