Top 20 Proscan 32LA30Q Television - Page 4 Questions & Answers

Ok i have several remote codes for you:

1.10178 or 10466

then try
1.0047 or 0747 or 0030

Finngers crossed for you!

It can be bad power supply or the main board is bad.
Parts: http://www.shopjimmy.com/catalogsearch/result/?q=Proscan+32LA30Q+

There are two places to look for the problems, the backlight inverter board and the power supply. Look at the power supply first since it is easier to get to, look for burnt parts, bad capacitors, etc.
http://en.wikipedia.org/wiki/Capacitor_plague
PARTS: http://www.shopjimmy.com/catalogsearch/result/?q=Proscan+32LA30Q+
Please post back what you find.

there is no audio out in my proscan 32LB30Q tv so there is no way for me to hook it up on my amplifier....

Look at the power supply first; look for burnt parts, bad capacitors, etc. Look to see if you have any DC voltage at the output connectors.
http://en.wikipedia.org/wiki/Capacitor_plague
Parts: http://www.shopjimmy.com/catalogsearch/result/?q=Proscan+32LA30Q+
Please post back what you find

It is your main control board. That controls the entire television set.

Here is the PROSCAN website:
http://oncorpus.com/

Here is a link to the manual:
http://www.oncorpus.com/down/ENG/26LA30Q,32LA30Q%20UM.pdf

I didn't fix it. I was looking for someone that said they could fix my problem. You were going to refer me to someone that may or may not fix it. I don't want to pay for that.

follow this link to download the drivers:

http://welcome.solutions.brother.com/bsc/public/us/us/en/dlf/download_top.html?reg=us&c=us&lang=en&prod=dcp350c_all

very poor to none and very poor support

if using RCA connector cables, connect the left and right audio cables to D and D1, then connect the Video cable to the video connector right above the S Video port.

Found these codes on the website for PROSCAN. www.oncorpus.com, for youmodel television.I hope this help you with your problem. UNIVERSALREMOTE CONTROL CODE LIST
For Universal Remote Control brands listed below, please use accompanying Proscan codes
and refer to your Universal Remote Control User Manual for basic instruction for changing TV code to
operate Proscan model.
Proscan codes for Sony TV=8003,8012
Proscan codes for Philips TV=1005,1006,1007,1035,1064,1216
Proscan codes for other universal remotes=272,132,134,116,040,016,024,056,019,262

Proscan 0 0 4 7 ,0 7 4 7 There are only 2


Plrease rate the help++++Thanks for using FIXYA

autoprogram,or use channel 3 from the vcr.,and run the dvd into the vcr which can be set on channel 4 on the back on alot of them

DIRECTV Specials DIRECTV Packages DIRECTV Receivers DIRECTV DVR DIRECTV HD DIRECTV vs. Cable DIRECTV vs. Dish DIRECTV Sports Home > Remote Codes DIRECTV Remote Codes TV CODES VCR CODES DVD CODES STEREO RECEIVER CODES
STEREO AMPLIFIER CODES DIRECTV RECEIVER CODES

Program TV Code
1. Turn on the TV.
2. Locate the 5-digit code for your TV.
3. Slide the MODE switch to the TV position.
4. Press and hold the MUTE and SELECT keys at the same time until the green light under the TV position flashes twice, then release both keys.
5. Using the number keys enter the 5-digit code for your brand of TV. If performed correctly, the green light under TV flashed twice.
6. Aim the remote at your TV and press the PWR key once. Your TV should turn off. If it does not turn off, repeat steps 3 and 4, trying each code for your brand until you find the correct code.
7. Slide the MODE switch to the DIRECTV position. Press TV POWER. Your TV should turn on.

Program DVD, VCR, Stereo Receiver, and Stereo Amplifier Code
The AV1 and AV2 switch positions can be setup to control a VCR, DVD, STEREO, second DIRECTV Receiver or second

1. Turn on the component you wish to control (e.g. your DVD Player).
2. Locate the 5-digit code for your component.
3. Slide the MODE switch to the AV1 (or AV2) position.
4. Press and hold the MUTE and SELECT keys at the same time until the green light under AV1 (or AV2) flashes twice, then release both keys.
5. Using the NUMBER keys, enter the 5-digit code for the brand of component being set up. If performed correctly, the green light under the selected position flashes twice.
6. Aim the remote at your component and press the PWR key once. The component should turn off; if it does not, repeat steps 3 and 4, trying each code for your brand until you find the correct code.
7. Repeat steps 1 through 6 to set up a new component under AV2 (or AV1).

Unable to Find Correct Code
If you were unable to find the code for your brand of TV or component, you can try a code search. This process may take up to 30 minutes.
1. Turn on the TV or component. Insert a tape or disk if applicable.
2. Slide the MODE switch to the TV, AV1 or AV2 position, as desired.
3. Press and hold the MUTE and SELECT keys at the same time until the green light under the selected switch position flashes twice, then release both keys.
4. Enter 9-9-1 followed by one of the following four digits:
Satellite - 0
TV - 1
VCR/DVD - 2
Stereo Receiver/Stereo Amplifier - 3
5. Press PWR, or other functions (e.g. PLAY for VCR) you want to use.
6. Point the remote at the TV or component and press CHAN+. Repeatedly press CHAN+ until the TV or component turns off.
NOTE: Every time CHAN+ is pressed the remote advances to the next code and power is transmitted to the component.
7. Use the CHAN- key to step back a code.
8. When the TV or component turns off, stop pressing the CHAN+ key. Then, press and release the SELECT key.
NOTE: If the light flashes 3 times before the TV or component responds, you've cycled through all codes and the code you need is not available. You must use the remote that came with your TV or component.

Universal remotes are not all that great. I would just use what was made for the TV.
This web site here is the best price going right now for a replacement remote. $29.95
http://www.proscan.newremotecontrol.com/catalog_item.php?catnum=E20KQ00

here is the complete list of codes, and proscan is in there

http://www.hifi-remote.com/ofa/devices-tv.shtml

Are the speakers external or build in?

Anyway, my suggestion would be to replace the speaker unit because something like water, dust, dirt etc is causing the problem.

You may find it cheater to purchase some high quality external speakers for this unit.

I hope this helps.

hi most of the time ur screen sits on 2 bolts coming from the base and screen sits on top.....
if u cant find it go in contact with PROSCAN and they will help u to get it off