Top 20 Polaroid FLM-2632 Television - Page 7 Questions & Answers

You are trying to use a box remote for the television? https://www.xfinity.com/support/remotes 3, 4, and 5 digit codes https://codesforuniversalremotes.com/remote-control-codes-for-polaroid-tvs/ https://www.google.com/search?q=Polaroid+TLA+-01911c+replacement+remote

see if this helps copy and paste https://www.manualslib.com/manual/1051795/Polaroid-L9.html ..

Nope

Hi Amanda...If it's an older LCD set it could be a capacitor issue, try putting a hair dryer at the fins in the back of the set and let it run for a few minutes then see if it comes on

Replace the tcon board

Possible power board issue

Question edited for clarity, full 'make model (what it is)'. Question moved from Computers to Polaroid Television. No unfortunately not. It is a basic HD television, but not a 'Smart' television and has no internet connectivity. It is also 14 years old. https://www.directutor.com/content/user-manual-polaroid-polaroid-tlx-04243b https://www.google.com/search?q=TLX04243B+review ..

Try the flashlight test to see if you can see a picture with an artificial light, I think you have bad LED backlights but this test will confirm that

Enter one of the programming code from the list 0004 0005 0009 0138 0130 for your POLAROID TV (including LCD, LED and Plasma) device. enter it using the Number Buttons. The LED flashes once after entering each digit. If the code is accepted, the LED flashes twice after the last digit is and then turns off.

VIZIO Universal Remote Setup codes for POLAROID TV ...

and here is you manual if you need it. https://www.directutor.com/content/user-manual-polaroid-polaroid-tlu-02241c

Chances are your tcon board is bad, here is the part number, finding one may be difficult CMO 35-D019140

Bad power board

Buy an amplified antenna at an electronicstore or some discount or closeout place...about 10$

it might be a software problem.

Your EEPROM is defective in the main board, if you have the equipment and skill to change it that's the way to go but unless youve done soldering on small devices replace the entire main board. I'ts possible this TV has a main-power combo board

You can contact the Customer Support team here; [email protected].

Your going to need a new main board

Fault with the main power supply regulator board. Check and replace damaged component/s at its main power regulator [SMPS] section circuit. Contact any service technician. If you wish to get some details; check the site linked here. Pull up older posts. http://electronicshelponline.blogspot.com/ It will be best to replace the power supply regulator board as card basis rather than making "Surgery" to it; which usually will make loss for both money and time. Even though you can make it right, it will cost around an amount equal to the cost of a new board; including the cost of (spare parts + service charge) More to say, most of the spare parts to it will be difficult to get from open electronic spare part market. This is true to most of the flat panel TV power supply boards; irrespective of its brand and screen size. Search the site by type in the brand name of your set, in its search bar at the right side column, and press enter. See it in Webview by mobile. Mobile View has no search box.

The manual doesn't mention anything about removing the back panel or doing DIY repairs. But you can phone them and they will give you advice for free. Questions? Need some help? Call our 1-888-896-9859 helpline: https://www.directutor.com/content/user-manual-polaroid-polaroid-tlx-04243b ..

Use code search on your GE URC to find something that works. You may need separate codes for TV and DVD player. If a search through all codes stored in the URC fails, try a different one.

go into audio settings and change to variable volume