Nordic Track NordicTrack C2150 Treadmill - Page 8 - Answered Questions & Fixed issues

You need to call Icon ASAP and get a tech out under warranty to fix the issue.

Lube the treadmills deck belt inmediately2= lube the rollers bearing too3=measure the input voltage motor, if there are the motor need repair4) measure the output board, for input voltage motor, if there are NOT the board is faulty.God bless you

see the video: God bless you

yes YOU must RUN the software calibration, for diagnose and troubleshooting, read your instruction manual, if you do not have download fro free. www. fitness.manualsonline.com or www. iconservice.comGod bless you

see your instruction manual, and proceed or contact customer service. from www. nordicktrack.comGod bless you

1) Lube the deck belt, this happen because the electronic system protect the system and shut down.the cause is deck worn.2) Lube the rollers bearing too.3) Measure the input voltage motor, if there are the motor need repair.4) Measure the output voltage board, for input voltage motor, if there are Not the board is faulty.God bless you

1)Lube the deck belt,this is happening because the lack of lube produce enough friction between deck vs deck belt, and result in shut down.2)lube The rollers bearing very well3)measure the input voltage motor, if there are the motor need repair4) measure the output voltage board, for input voltage motor, if there are Not the board is faulty. see the bloc diagramGod bless you

1) you must LUBE THE DECK BELT+ ROLLER BEARING.2) Test the input voltage motor, if there are the MOTOR is faulty need REPAIR.3) Test the output voltage board, for input voltage motor, if there are NOT the board is faulty. 4) SEE THE BLOCK DIAGRAM, whatever component can be faulty.However you must test the power cord for short circuit between cable, repair, and look inside according the BLOCK, and proceed with logic, see any loose wires, or some wires touching the carcase, some filter, coil, power supply USE the VOM. God bless you

1) Adjust the reed switch, clean, and tigh the connector wires very well. see the diagram attached.2) tigh the ribbon cables from keypad, clean it with special spray contact the keypads.. tight the wires connector from display board vs lower board.AFTERT your fix it RUN the s. caibrationGod bless you

1) Adjust the Reed switch, see the diagram attached, clean, and tigh the wires connector very well.2) Tight the ribbon cables from keypads+ tight the wires connector from display board vs lower board. see the block diagram for better understanding. 3) Run the software calibration for diagnose, troubleshooting.God bless you

1) Lube very well the deck belt, maybe you have deck belt worn by lack of maintenance schedule proceed with the instructio manuall , and adjust it.2) Test the drive belt and replace it.2a) LUBE the rollers bearing front, and rear3) Test the input voltage motor, if there are , the motor need repair.4) Test the output voltage board, for input voltage motor, if there are not the board is faulty.5) Try to run the software calibration for diagnose, and troubleshooting.sincerely. God bless you

if the plug is bend or something like. Try with some plyer to repair.Otherwise you need to replace the plug. You can go to www.fitnessrepairparts.com and to buy.Maybe you will need some electrician,if you do not have the experience.sincerely. God bless you

Dear Sir:1) Lube the treadmill in according with the instruction manual.2) The reason is lack of lube by maintenance, that produce enough friction with shut down for to protect electronic system.3) Test the deck belt if is worn, and replace it.4) Test the rollers bearings5) See the bearing motor6) Test the input voltage motor coming from the output from the main motor board,, use DVOM.7) See my personal TIPS for HELP.sincerely. God bless you

Dear Sir:Please see the attached diagram for adjusting the reed switch, clean very well, and tigh the connector wires.sincerely. God bless you

Dear Sir:Adjust the reed switch. see the attached diagram.proceed according with your instruction manual, if you do not have go for free download: www. fitness.manualsonline. com or www. iconservice. com sincerely. God bless you

Dear Sir:Go for free download: www. fitness. manualsonline. com sincerely. God bless you

need a owners manual for c2si model #30076.0

oil or try 2 move the little button in the key hole it is stuck or not getting contact

Dear Sir:There many possibilities: 1( False signal to due flexible cable loose *tight( 2( console display faulty 3(main motor board faulty 4(the pot attached to the elevation motor need adjustment 5( the gearing can sliping 6( Main motor damaged.Try to RUN the software calibration for easy diagnose and trouble.See my personal TIPS for HELP.sincerely. God Bless you.ernesto cuadramanagua, nicaragua. c.a

Dear Sir:If you can the change the resistor is o.k ,depending about your skill in electricity or electronic.Remember when you change, but the exactly as indicated in the board. For example the resistor has color code, I can recomend you can buy some chart from Radio Shack, for you will see the exactly value+tolerance)Very Important+Power of resistor.Meanwhile, if the resistor is Sparking, is indicating there are some short-circuit in the board. By that reason when you change the resistor if the trouble persist, you must send the board or call some service tech from some company for assist you in this problemOther alternative that you have is RUN THE calibration SOFTWARE,that is coming with your equipment, the instruction most of them coming from the Hood of the motor, other your must use your Instruction Manual.This is important for easy Diagnose and Troubleshooting from your treadmill. Remember this very Complex equipment electronic.sincerely. God bless you.ernesto cuadramanagua, nicaragua. c.a