Nordic Track NordicTrack C2150 Treadmill - Page 7 - Answered Questions & Fixed issues

go HOOD cover motor follow the steps or ready your owner manual, and RUN the software calibration for easy diagnostic and fix it.TheSteps for Newer Style Console Calibration1. Locate the calibration area on therear or underside of the console (a hole, near the console\'s center, that goesthrough to the electronics board. (This hole should not have a screw init.)2. Insert a pencil (eraser end),into the hole and feel around for the cal button (will click whenpressed).3. Press the button 2 times(with the pencil eraser). The first click should show CL11 in theconsole, the second click should show CL21.4. If the process was done correctly,and CL21 appears in the console, you are in "calibration mode."The next few steps consists of pressing buttons on the consoleand observing settings. This will not require any other tools.5. Press ENTER. CL22 should display inthe TIME window and (??) in the SPEED window.6. Press ENTER. CL23 should display inthe TIME window and (??) in the SPEED window.7. Press ENTER. CL24 should display inthe TIME window and (??) in the SPEED window.8. Press ENTER. CL25 shoulddisplay in the TIME window and (??) in the SPEED window.9. Press ENTER. CL26 shoulddisplay in the TIME window. You should then see the letter"E." 10. PressENTER. You should see "SS" or "55" in the console. 11.Push the STOP/START button. For safety, at this point, you should step off, or beoff, the treadmill.12. Pushthe ENTER button. The walking belt should start to move, accelerate to maximumspeed, then stop on its own. 13. Whenthe belt stops, the incline should self test by raising to itshighest incline position, then lowering back down to its lowest position. 14. Oncethe incline test is complete, push the POWER button 2 times. The unit shouldshut off and the console should go completely blank. If thishappens, the treadmill is done calibrating and is ready for use.If the letter"F" appears in the SPEED or INCLINE window when the power button ispressed 2 times, the treadmill is indicating a failure somewhereeither in the SPEED or INCLINE (depending on the window the"F" appeared in). Troubleshooting the failure would be the nextstep. God bless you

follow this steps and fix it. God bless you

Step 1

Plug the power cord into a UL 1449 single-outlet surge suppressor and then plug the surge suppressor into an electrical outlet that is not GFCI-equipped if the power does not turn on. If the treadmill is plugged in and the power still does not work, make sure the key is in the console and that the Reset/Off circuit breaker has not been tripped. Press the switch to "Reset" if it has been tripped. Sponsored LinksGym Equipment Choose from 1M+ Verified Suppliers. Contact Directly & Get Live Quotes! www.alibaba.com/Gym-Equipment

Step 2

Check the Reset/Off circuit breaker if the power switches off while in use. Wait five minutes and switch the button to reset. Check that the power cord is still plugged in securely; pull the plug out and plug it back in after five minutes. Pull out the console key and reinsert to see if the machine will turn back on.

Step 3

Place the chest pulse sensor tightly right underneath your pectoral muscles or breasts for it to operate properly. Position it lower or higher on your chest if it does not work properly. Wet the electrodes with a saline solution. Walk near the walking belt's center within an arm's reach of the console.

Step 4

Remove the console key and unplug the treadmill to loosen the walking belt if it slows when in use. Turn the rear roller bolts counterclockwise with the hex key 1/4 of a turn until you can lift the walking belt's edges 3 to 4 inches from the platform.

Step 5

Remove the key and unplug the treadmill to adjust the walking belt if it is off-center or slips when in use. Loosen the rear roller bolts with the hex key and reposition the walking belt. Tighten the roller bolts. Walk on the treadmill to determine if the walking belt is centered. If not, loosen the roller bolts again and make adjustments until the walking belt is centered.

Step 6

Recalibrate the incline system if the treadmill's incline does not adjust correctly. Press the "Incline" button and remove the console key. Wait a few seconds and replace the console key. The incline will automatically recalibrate by moving to the maximum incline level and then the minimum level.

Step 7

Press the "Stop" button for a few seconds to turn off the demo mode if the console display stays lit after you remove the console key.

Run the s.calibration for easy diagnostic and fix it. God bless you

adjust the REED SWITCH, see the diagram attached, Clean it+test for open or faulty+tigh the connector very well,2) tight the ribbon cable inside and clean from oxide or corrosion+tight the upper +lower connector from oxide or corrosion.3) reset use small pencil erase for to click.God bless youGod bless you

see this The most likely cause of the problem is a worn treadmill belt and deck. Most of the time its caused from not lubricating between the treadmill belt and deck. This causes friction and the surfaces wear putting greater stress on the electronics. The treadmill is shutting down to protect the electronics. You should stop using the treadmill and have a technician check it.If it sounds like metal rotating on metal then it could be roller bearings or motor bearings. Its best to have the treadmill work carried out by a technician in the workshop. Most of the time the bearings will have to be pressed out and the new ones pressed inGod bless you

please LUBE the deck belt+rollers bearing front and rear+test the drive belt motor, and replace if necessary. see the video attached.God bless you

see the video attached and fix it. God bless you

tread has to be in 0 incline or close but you lift as far as you need to line up the ends of the latch bar installbolts done

please RUN the software calibration and fix it.God bless you

The Steps for Newer Style Console Calibration

1. Locate the calibration area on the rear or underside of the console (a hole, near the console's center, that goes through to the electronics board. (This hole should not have a screw in it.)

2. Insert a pencil (eraser end), into the hole and feel around for the cal button (will click when pressed).

3. Press the button 2 times (with the pencil eraser). The first click should show CL11 in the console, the second click should show CL21.

4. If the process was done correctly, and CL21 appears in the console, you are in "calibration mode." The next few steps consists of pressing buttons on the console and observing settings. This will not require any other tools.

5. Press ENTER. CL22 should display in the TIME window and (??) in the SPEED window.

6. Press ENTER. CL23 should display in the TIME window and (??) in the SPEED window.

7. Press ENTER. CL24 should display in the TIME window and (??) in the SPEED window.

8. Press ENTER. CL25 should display in the TIME window and (??) in the SPEED window.

9. Press ENTER. CL26 should display in the TIME window. You should then see the letter "E."

10. Press ENTER. You should see "SS" or "55" in the console.

11. Push the STOP/START button. For safety, at this point, you should step off, or be off, the treadmill.

12. Push the ENTER button. The walking belt should start to move, accelerate to maximum speed, then stop on its own.

13. When the belt stops, the incline should self test by raising to its highest incline position, then lowering back down to its lowest position.

14. Once the incline test is complete, push the POWER button 2 times. The unit should shut off and the console should go completely blank. If this happens, the treadmill is done calibrating and is ready for use.

15. If the letter "F" appears in the SPEED or INCLINE window when the power button is pressed 2 times, the treadmill is indicating a failure somewhere either in the SPEED or INCLINE (depending on the window the "F" appeared in). Troubleshooting the failure would be the next step.

please LUBE the deck belt + rollers bearing too. See the video and proceed according. This happen because the lack of maintenance schedule.If after you fixed the problem remain , is TIME to replace the old board deck.God bless you

1) replace the batteries by new ones, with the same type, and polarityclean the contacts batteries v. well2) tight the ribbon cable from keypad , clean it and tight the connector.3) Adjust the REED SWITC H, see the diagram attached. clean it. test for open or faulty. Tight the conector very well.God bless youG

Try this website, please:http://www.livestrong.com/article/410922-the-controls-are-not-working-on-a-nordictrack-treadmill/

1) adjust the REED switch , see the diagram, clean it and tightthe plug very well2)test the fuse+ c.breaker see the diagram , replace or reset2a) test the main switch for open or faulty and replace3) if after this the problem remain.4) you have problem with the power supply:capacitor, transformer, diodes,etc Replace the main boadsee the block diagramGod bless you

I not shure , but you can try it with software calibration-However you can get answer more explicit from company via chat or phone. contact themGod bless you

1) Lube the deck belt, this happen because the lack of maintenance according with the instr. manual. This produce shut down, for to protect the electronic system. Maybe you have a worn deck belt.3see the video and proceed according. LUBE the rollers bearings too.3) test the input voltage motor, and if there are voltage, the motor need repair.4) test the output voltage board, for input voltage motor, if there are NOT the board is faulty. see the diagram attached.God bless you

please see the video and proceed according with common sense.God bless you

go www. fitnessrepairparts.com or www. treadmilldoctor.com and buy it.or go to www. nordicktrack.comGod bless you

see the block diagram: I recommend you to RUN the software calibration for diagnose, troublehooting, and fix it Before to exchange the control boar, maybe your have the motor for repair. or another section and the transformer for power supply.God bless you

Run THE SOFTWARE CALIBRATION for diagnose, troubleshooting, fix it.see the diagram attached,LUBE the gear and shaft from motor.God bless you.

1) Lube the elevation motor, see the diagram, parts gear + shift2) adjust the POT, for a little and see if there are better improve.3) RUN the software calibration for diagnose, troubleshooting, fix it.God bless you