Top 20 Linksys Wireless-G WRT54GS Router (e125894) Questions & Answers

Reset the router to default....the default username and password is usually on the bottom of the router..then open a web page on your pc and connect the router with a network cable..type 192.168.0.1 or 192.168.1.1
Use the generic name and password to logon....once logged in, configure username and password and wifi...once setup..save and exit..disconnect and connect router to internet modem...log onto pc and look for your wifi neteork name..cheers

Do you know your SSID and password for your wireless account? I’m happy to help further over the phone at https://www.6ya.com/expert/tami_f8d2d553d5094045

LOST ROUTER LOGIN PASSWORD If you have forgotten your personal router login password there is no way to recover it. You will have to reset the router. This means all the settings on the router will be reset to factory defaults. It also means that all your connected devices will need to be connected again with the new security information (WEP, WAP, etc,) . You will need the default admin login name and the default admin password. This can be found in the user guide that came with the router. This can usually be found online at the router manufacturers site. There is usually a button or a switch hidden in a pinhole opening on the back of the router. Pressing and holding the switch for 10 seconds or so will cause the reset and usually the LEDs will flash and blink for several seconds as the router firmware resets and clears out the old information. If you are trying to get into someone else's router illegally there is no way to find out their login password. For future reference, write the password down, or a hint at what the password is, on a piece of tape and secure it on the bottom of the router. I use my cell phone memo function to store all my passwords. Linksys Home Networking

http://downloads.linksys.com/downloads/WRT54GS_V72_QI_NC-WEB,0.pdf

I had some also facing same issue with my router. I tried a lot however nothing helped me, I just visited LINKSYS Tech Support and made a call on their toll free. I got instant help for my router by a certified technician. Hope this will help you

It sounds like you may be having IP address conflicts. Many Xbox users have a fixed IP address set in their unit and then have a Port Forwarding done in the router to provide faster play. If you reset the router all this is lost. Then what can happen is that the router will assign a device the reserved IP address of the Xbox. When you turn the Xbox on, then it cannot connect as there is another device already assigned that address. Reconfiguration is required to prevent IP conflicts.

Have you rebooted the computer and the Kodak. Try deleting the device in the compter and reinstalling.

To reset the Linksys back to the default settings - Press and hold the pinhole RESET button at the back of the router with the power ON for 20 secs. then release the RESET button. To connect to your wireless router, the router's wireless settings needs to be configured with the SSID, encryption etc. and also the wireless cards in all the laptops/computers needs to be configured with these router's wireless settings. Then the laptops/desktop computers can communicate with your wireless router. Connect a LAN cable from the Linksys to the LAN port on your computer. Open a browser and enter the Linksys configuration URL http://192.168.1.1 The default login = admin The default PW = admin You can protect your router by changing the default admin PW (write it down and put it in a safe place) Go to the wireless configuration and set up the SSID and WPA or WPA2 encryption to protect your wireless network and Internet from unauthorized access. Now apply these settings to the wireless card in your laptop/computer. To secure your wireless network from unauthorized access, please click on this link and follow my instructions :- http://www.fixya.com/support/r3559128-wireless_router_security

your router is not compatible with your network. There are two networks, g and n. You can get a router that is compatible with both but if you have a g network and an n router they can't communicate.

Check your Acer has the wireless device and driver been installed.If so then - To connect your computer to a wireless router, you click the Refresh network list, then Choose your wireless network and then click Connect to your secured Wireless Network, it will asks for a Network Key before allowing you to connect into your wireless network. This Network Key is either the WEP, or WPA or WPA2 Encryption key that is used to configure the Wireless Router. The Passphrase is an alternate way to setup the Encryption key. When you are requested for a Network Key, you can just enter the Passphrase that was used to configure the Encryption key in the wireless router. http://www.fixya.com/support/r5270415-network_password_network_address For information on securing your wireless network, configuring the wireless router and configuring the wireless card in the laptop/computer, please click on this link and follow my instructions :- http://www.fixya.com/support/r3559128-wireless_router_security

TYPE 192.168.1.1 FOR ACCESS TO ROUTER SITE....BEST, GERSHON....

Normally,default username and password of Linksys router are 'admin' .orusername can be blank and password is 'admin'. I think ,you must refer to your wireless router support manual. It can vary depending on your router brand or model . You can also visit online to check model no and their default login details.

You do not have to use the cd or driver.Shutdown your PC. Unplug the power from the router and the cable modem.Wait 30 sec. then plug in the power to the cable modem, wait 30 sec. then plug the power to the router. Wait till you have "Internet" light then restart your PC. The PC should pick up an IP address and you should be able to get on-line. This is if you have a cable service provider. If you have DSL, the router needs to be configured with PPOe. I’m happy to assist further over the phone at https://www.6ya.com/expert/joe_8b8c2cd6ce148309

Try the following procedure on a computer that's directly connected to one of the router ports with an ethernet cable. This procedure will not work if you're connected wirelessly. Open a web browser, such as Internet Explorer, and type in http:192.168.1.1. A window should pop up asking for a user name and a password. Don't enter a user name and type admin for the password. Hit ok. The router setup screen should come up. Click on the Wireless tab and then the Wireless Security sub-tab. You should be able to see your present wireless network security key on this screen. You can also use this screen to change the key if you want. If you want to make some changes first select the security mode you want to use. I believe WPA gives better security but I've had some trouble using it on older computers. I use WEP. I've been able to get this encryption scheme to work with all of my computers. Next select the type of encryption. I like 128 bit 26 hex digits. Next enter a pass phrase and hit generate. The pass phrase is like a password. It should now generate four 26 character keys made up of various letters and numbers. Write down the first key and make sure you've checked the 1 box for default transmit key. Save your setting and exit. You wireless network is now secure. If you try to connect to it using a wireless device you will be prompted for a security key. Depending on the operating system you're running, you may just be able to enter the pass phrase or you may need to enter the 26 character key you wrote down. You should only have to do this once for each of your wireless devices. After the first time they connect to the secured network they should automatically remember the security code. I hope this advice helps you out.

The sticker on the bottom of the router will have a symbol more than likely that looks like the 2 arrows on the top. When you are looking at the sticker that has the MAC ID, there should be one that has that symbol and is just 7-10 numbers. That should be the owner Pin it is looking for.

Unfortunately, no. The only way to access your network again is to reset the router by holding down the reset button on the back (you might need to unplug it, then plug it back in while holding the reset button). That will reset your web interface (navigate to 192.168.1.1 in your browser while connected to the router)'s username and password to some form of the following:

Username: admin
Password: admin
Username: admin
Password: password
Username: admin
Password:

NOTE: The last combination is a blank password.

Once you've entered your router's web utility, you can set up your wireless again. Don't forget to write down the password...I wrote mine on the router itself, because honestly nobody can see it because it's in my house, so I don't have to worry about it being stolen.

If the router is yours and you forgot the password, you can reset the router. After that you can reconfigure your network access.There is a RESET button on the back that you can press to rebootIf the router is not yours, well, you have no business trying to krack the password.

This is a simple operation if you know how to log on to your router
First step log on with a web browser 192.168.1.1 leave user id blank and type admin in password box
This will take you to opening page of router click on wireless and then security. This is the page where you set your password to make wifi secure!
Also you need to set password for Router open page above. Its better to remove default password and use your own password. click save at the bottom.

WRT54GS may be more reliable router and you can continue to use it. Try power cycle first check cables! If no improvement you can reset! that will bring it factory default!
Other important matter is check the firmware upgrading firmware is a good solution for these kind of problems!
Currently available routers are much better if you are willing to get a new router N router is the way to go! They wider area coverage and faster network speeds!
good luck!