Linksys Logo

Linksys Recent Questions, Troubleshooting Help & Support

Do you work here? Claim your company

  • 856 Products
  • 82K Answers
  • 2M Views

Linksys Official Support Changing the router wireless network name and...
The above link is instructions for changing network name and password using the Linksys Connect software.

Below is the user guide if you need it.
http://downloads.linksys.com/downloads/userguide/MAN_E2500_3425-01547E_E-Router_EN.pdf

Linksys By Cisco... | Answered on Jan 31, 2019


Check the available memory on your PC. It may be limited and far too small for the operation you are running. Same thing happened to me

Linksys... | Answered on Jan 31, 2019


Press and hold red reset button on back of unit for 30 seconds

Linksys... | Answered on Jan 31, 2019


Default user names:
  • Linksys BEFW11S4, WRT54G: admin
  • Linksys EtherFast Cable/DSL Ethernet routers: Administrator
  • Linksys Comcast routers: comcast
  • All other Linksys routers: [none]
Default passwords:
  • Linksys BEFW11S4: [none]
  • Linksys Comcast routers: 1234
  • All other Linksys routers: admin

Linksys... | Answered on Jan 31, 2019


SADLY WITHOUT IT BEING A RECEIVER THERE MIGHT NEVER BE A WAY YOU CAN LINK IT UP

Linksys... | Answered on Jan 29, 2019


Check the wall outlet for power, using a lamp or such. If you can get a multi-meter, set the meter to Volts-DC between 12 and 20. Plug the power supply into the wall outlet and test the other end for voltage. The power supply should tell you its output so the reading should be more than a couple of volts. If it is less or ZERO the power supply is dead. If it has power, then open the router and check for a fuse. If the fuse is dead, replace. If there is no fuse or the fuse is OK then the router may be dead. Best of luck.

Linksys... | Answered on Jan 10, 2019


The Problem is all Lan port light are solid and power light is dim. And you hear a very low hizzz noise from the router.

Solution is

I Fixed it with a new 470uf 10v cap ps its the one next to the circle copper wrapped wire than CS29 is written next to it.

Just replace it and it will start work again.
12_22_2018_4_18_59_pm.jpg

Linksys WRT300N... | Answered on Dec 22, 2018


What is blocked?
Please explain in detail.
If your router is not working then I will suggest you to reset the router and reconfigure the router.
create a new wireless network and see if that works.

See How to setup Linksys router without CD.

Watch video:
How to reset Linksys router




Linksys... | Answered on Nov 28, 2018


It's a wireless router, so you may not need to use a port at all.

You can connect to any of the ports numbered 1 through 4. The yellow Internet port should connect to your outside network. (Cable modem or router or Ethernet port from your Internet service provider.)

Linksys E900... | Answered on Nov 27, 2018


See if any of the solutions proposed at the bottom of the page (click here) fix your problem.

Linksys... | Answered on Nov 26, 2018


If you already have a cable router, then you don't want to use a wireless router. You will want to use a wireless access point instead.
The reason for this is that anything plugged-in to your cable router will not be able to access anything connected to the wireless router due to the NAT firewall in the wireless router.
If the wireless router has the option to make it a "Gateway", then that will fix this issue; otherwise, take the router back and buy a wireless access point instead.
As for how you hook up the wireless router to the cable router, you have to unplug the power cord of the cable router for about 15 minutes before hooking the Ethernet jack from it to the wireless router.
Once the 15 minutes have passed, you then can plug the Ethernet cable from the wireless router "WAN" port into an Ethernet port on the cable router and then plug-in the power cord of the cable router.
Once the cable router is finished syncing-up, the cable router should provide an IP address to the wireless router.
If you really have a cable modem instead of a cable router, then you won't have to put the wireless router into gateway mode.

Linksys... | Answered on Nov 26, 2018


I am providing you with two links from linksys. The fist link is the user guide, and the second is the quick installation guide. Between these two guides you should be able to set the router up with out any issue.

http://homedownloads.cisco.com/downloads/userguide/1224638367343/WRT54G-v1.1_ug.pdf
http://homedownloads.cisco.com/downloads/quickinstall/1224638367420/WRT54G-v1.1_qi.pdf

hope these help

Linksys... | Answered on Nov 22, 2018


Lets see if this works out for ya.
1. In your browser go to http://192.168.1.1
2. The user will be "admin" and the password field leave it blank
3. Go to the Setup Tab
4. On WAN Connection Type make sure it is set to "Obtain an IP Automatically"
5. Go to the DHCP tab and make sure it is enabled
6. Unplug the Roadrunner modem and the Linksys Router.
7. Wait around 15-30 seconds
8. Plug the Roadrunner modem in and wait until all the lights except the ethernet/computer connection are on.
9. When they are all on plug the Linksys router power back in
10. Wait around 30 seconds and see if your getting a connection
Otherwise get back to me. Good luck.

Linksys... | Answered on Nov 19, 2018


not really unless you were to run an ethernet cable from your existing network to a location outside of the current wi fi range.
A repeater would be better
https://www.tomsguide.com/us/best-wifi-extenders,review-2225.html
It hears the wi fi signal so you put within the signal range near where the signal still can be heard near the extent of the current wi fi range. It will hear the signal and then re-transmit it to extend the signal range .

You might be able to use a gain antenna of 5dbi 2dbi is lost in the cable usually so it is 3dbi which is twice the level
http://computers.mwave.com.au/electronics/High-Gain-Antenna

another method would be a omni directional antenna facing the coverage range . But it is beaming in one direction .
which means more signal strength in one direction
https://www.mwave.com.au/product/draytek-ant1207-highgain-omnidirectional-indoor-antenna-black-ac04622

Linksys... | Answered on Nov 12, 2018


I think you can try upgrading the firmware on your router,

Connect the computer to the router.
Download the latest firmware.
Open the setup page of the router and upgrade the firmware.
After upgrading the firmware, reset the router and reconfigure it manually.

See How to upgrade firmware on Linksys router.

Watch video: Linksys router setup

Linksys WRT120N... | Answered on Oct 25, 2018


It depends on the power capability of the EA7400! Usually, those ports are rated at 500ma, or 0.5 amps each. If you plug in a non-powered hub into one of the ports, it will draw power from the EA7400 to operate. If the power draw needed exceeds the capability of the port, it won't work properly. A powered hub relies on an external power source. In that case, only data collisions (oversaturating the ports) need to be considered.

Linksys... | Answered on Oct 21, 2018


WHEN NOTHING CAN CONNECT TO WI-FI
Some time router faced the problem like not be connected to any device, plug your laptop into the router directly using an Ethernet cable, and see if you can be connected that way. If there are connect then you understand the problem in your Wi-Fi router. But if it doesn't, then your network connection may be poor.
Resetting your router can fix a myriad of issues and an inability to connect is one of them. Press the reset button on the back of the router with a paperclip for 30 seconds and the router should default to factory settings. If you can't understand for the setup contact our customer service number and get solution.
Our customer service is making fully satisfied for the customer who wants to help with own budget, who the customer is notable for that solution don't worry we are providing support service for your problem solution contact with us by dialing the toll-free number and get instant solution immediate. If the customer needs to another technical service then visit our customer service website.

https://servicenumber.org/apple-routers.html

apple router support number-szv2cwqupz2tpg4ipc0cz0zq-2-0.jpg

Linksys WRT54G... | Answered on Oct 19, 2018


Linksys router is a good network service provider which provides high-speed network, multiple connectivities, easy for sharing network, easy for installation and etc. There are create some issue with this router when users install the driver, make connectivity to the system and other, we are a third party service provider and our service are guaranteed service by Linksys Router Customer Service Number which dial a toll-free number 1-833-284-2444 for 24*7 available, our expert technicians who are expert for the solving technical problem. The customer dial just toll-free number and get instant solutions.

Our service for Linksys Router When:-
l The router is not blinked network light
l Download speed is too slow
l Router driver installation
l Password recovery
l Create an account
l Sharing network
If the customer can't understand their technical problems don't worry we are here with any kind of technical solutions, we have expert technicians who are solving the problems, and they also are connected online service between customer system, it service available for 24*7 hr. or customer can visit for more technical solution with our website.

https://servicenumber.org/linksys.html


linksys router support number-si1bajcrgkj2y2nwpu00wjxp-1-0.jpeg

Linksys... | Answered on Oct 16, 2018

Not finding what you are looking for?

Ask a Question

Usually answered in minutes!

Top Linksys Experts

Prashant M
Prashant M

Level 3 Expert

2276 Answers

Les Dickinson
Les Dickinson

Level 3 Expert

18429 Answers

mark

Level 2 Expert

108 Answers

Are you a Linksys Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...