How do I remove the body to get to the A912746-0070A Oring?
IF IT WILL NOT COME OUT THEN THERE HAS GOT TO BE A SMALL SCREW OR SOMETHING HOLDING IT ON. IF AUCET IS TO TIGHT IT WILL NEED TO BE LOOSENED JUST A BIT. THERE MAY ALSO BE RUST OR DIRT IN IT AND YOU WILL NEED TO TAKE IT OFF & CLEAN IT WITH VINEGAR OR RUBBING ALCOHOL THEN PUT IT BACK ON.
1/21/2015 4:14:26 PM •
American...
•
Answered
on Jan 21, 2015
•
165 views
How to replace washer cartridge in bathroom tap
Turn the faucet to the closed position. Turn off the water to the faucet. Remove the handle. The screw that holds it on may be under a plastic cover. Unscrew the large nut. Remove the cartridge. Put the new cartridge in the closed position. Look at the old cartridge and be sure the new one matches the old one. Insert the cartridge. Replace the nut and tighten. Replace the handle. Turn on the water.
11/30/2014 3:34:34 PM •
American...
•
Answered
on Nov 30, 2014
•
260 views
No running hot water
These have a photoelectric eye , much the same as a motion sensor on an outside lamp, just pull this out, clean with a wet wipe, dry with a towel & replace, press the reset switch & your boiler should fire up producing lovely hot water
11/11/2014 8:41:13 PM •
American...
•
Answered
on Nov 11, 2014
•
166 views
How to remove bath tub pop-up stoppers
Put the lever in the open position so that you can grab the stopper. After you get a grip on it, put the lever in the closed position and the drain plug and rocker assembly will pull out in a horizontal direction.
10/28/2014 1:47:01 AM •
American...
•
Answered
on Oct 28, 2014
•
831 views
Ac unit buzzes and fan motor does not run when system turned on.
Your blower motor sounds like it is fried. I hope you have done something by now, 15 Oct 2014. But the best thing to do if someone is reading this and you get this symptom is to turn off the blower. If it is still under warranty, the new blower motor should not cost you anything except the labor and service charge. Different manufactures sometimes charge a small warranty charge to handle paperwork and shipping. If this recently happens to you, the most common cause is a voltage spike, like lightning strike, and it has blown the capacitor. If you do not have a capacitor on your blower motor, for example an x13 or an ECM type motor, then you will need to replace the control module and typically costs about $200. If your local dealer does stock the control module then the cost of most of these motors are around $500. Your best bet is to call a reputable repairman and get them to change it out. There is high voltage capacitors inside and can give you a good jolt if you happen to come in contact with the circuitry before the capacitor discharges.
Hope this helps.
10/16/2014 1:45:18 AM •
American...
•
Answered
on Oct 16, 2014
•
134 views
How to drain washer machine when lid switch is bad
very simple get to the wires that lead to the switch and jump them with a paper clip or alligator clip. its an open/close circuit based on resistance or no resistance there is nothing elecrtricre
9/17/2014 10:19:18 PM •
American...
•
Answered
on Sep 17, 2014
•
113 views
Repair crack in floor of acrylic shower
Hello their is a product called Plasweld,it comes in a handy tube,
Carefully scratch along the crack to allow the weld to come flush with the surface of the shower tray,MUST BE PERFECTLY DRY!
squeeze into the crack and it will find its own level ,this produce actually welds the plastic together
Good builders merchants should stock this item.GOOD LUCK
9/15/2014 12:00:54 PM •
American...
•
Answered
on Sep 15, 2014
•
131 views
Not finding what you are looking for?