Many lines on photos despite numerous cleaning, deep cleaning

Worn print head. And for what they charge for a stinking print head you can get a new printer for less with a warranty to boot!

It sound a though you have a blocked printhead. You would need to purchase a new one as the pattern check is the only test for it. Srri

insert your'e (prob. clogged) cartridge head surface into hot water for about 30 seconds. Then test the cart. over a paper tissue. If you see all colors test it on printer. If not you prob. need to vaccum the head. If all fails, replace cart.
good luck

f print quality does not improve by the standard cleaning of the Print Head, clean the Print Head deeply. Cleaning the Print Head deeply consumes more ink than the standard cleaning of the Print Head, so clean the Print Head deeply only when necessary.
1. Make sure that the power is turned on.

2. Clean the Print Head deeply. (1) Press the (Maintenance) button repeatedly until y appears.
(2) Press the Black or Color button.
The machine starts cleaning the Print Head deeply. Do not perform any other operations until the machine completes the deep cleaning of the Print Head. This takes about 2 minutes.

3. Check the print head condition.

When the deep cleaning is completed, the LED returns to the copy standby mode. To check the print head condition, print the nozzle check pattern.

See " Printing the Nozzle Check Pattern".

If the problem is not resolved, turn off the power and clean the Print Head deeply again after 24 hours.
If the problem is still not resolved, replace the FINE Cartridge with a new one.

See " Replacing FINE Cartridges".
If the problem is still not resolved after replacing the FINE Cartridge, contact the service center.

Printing the Nozzle Check Pattern
Print the nozzle check pattern to determine whether the ink ejects properly from the print head nozzles.

NOTE If the remaining ink level is low, the nozzle check pattern will not be printed correctly. Replace the FINE Cartridge whose ink is low.
See " Replacing FINE Cartridges".



You need to prepare: a sheet of A4 or Letter-sized plain paper

1. Make sure that the power is turned on.

2. Load a sheet of A4 or Letter-sized plain paper in the Rear Tray.

3. Open the Paper Output Tray gently, and open the Output Tray Extension.

4. Print the nozzle check pattern.

(1) Press the (Maintenance) button repeatedly until A appears.
(2) Press the Black or Color button.

The nozzle check pattern will be printed.

5. Examine the nozzle check pattern.
See Examining the Nozzle Check Pattern.

Examining the Nozzle Check Pattern

Examine the nozzle check pattern, and clean the Print Head if necessary.

1. Check if there are missing lines in the pattern (1) or horizontal white streaks in the pattern (2). (1) Check if lines are missing in this pattern. If yes, the cleaning is required.
See " Cleaning the Print Head".


(A) Good
(B) Bad (lines are missing)

(2) Check if horizontal white streaks are present in this pattern. If yes, the cleaning is required.
See " Cleaning the Print Head".

(A) Good
(B) Bad (horizontal white streaks are present)
Post back!

You will need a new printhead, QY6-0061-000, runs around $60.00 well worth it for your machine.

The other week I had the black print head clog up, requiring daily nozzle deep cleaning [a normal 'ocassional' maintenance function]. Thought I needed a new Print head, so anything worth a try.
I loaded up an old black cartridge [I load all my own......always have] with Isopropyl Alcohol and ran deep clean on that cartridge a couple of times, then repeat printed [6 times] a page full of the number 8 in about half inch character size, to get the alcohol through the nozzles. then Deep cleaned again 3 times, to wash it through the print head.

I reloaded the normal ink filled cartridge and ran the '8' page again till I got good black output. It has now been working without problem, daily, for over a week. Clearly if it's a Magenta only problem, the cleaning as described above would be a bit different, as the magenta is one of 4 colour cartridges.
My printer does quite a lot of work, and was bought at least a couple of years ago, being used daily for alpha numeric and photo printing work. This was the first difficulty I experienced with it.
Hope the above might help.Ken

The same problem here... Strange enough, it begun suddenly this september 1st.

print head clogged..if you remove it try cleaning it...or sink it in a boiled water to released clogged.....used tissue on cleaning...maybe its effective coz i repaired same printer you have...

sounds lke your yellow nozzle not working properly...had same issue on lexmark printer, ended up geting this epson...learnt from my mistakes...perhaps it ran dry? or you left the yellow cartridge out longer than the rest....only you might know what happened

just for info my printer wasn't printing much of anything black and color. If you hold down the middle button till the light on the top blinks twice it will give you a color test page. it should give you a grid to the right and to the left it should have the letter H and two blocks. If it doesn't you hit the middle button until the light blinks once and that is the cleaning. I have had to do almost 25 cleanings just today to finally get some results. Hope this helps you.