20 Most Recent Toshiba REGZA 47HL167 TV - Page 6 Questions & Answers

Hi,

connect a DVD player to the TV. If you still do not have sound, connect a headset to the TV. If there is no sound coming from the headset, it means your TV is have a defective sound ic.

When the sound ic is defective, you cannt hear any sound from the TV because the sound ic is responsible for bring out sound through the speaker.

Let me have a feedback on this issue please.

Yours sincerely.

Elect_Comp.

Hello,

Problem is in either power supply or the Y-Sustain board.

The Y-Sustain is a relatively large board out of which go connections to the side of the display; it's therefore closer to either the left or the right side of the display, has at least one rather large heat sink on it and fat power cables connecting it to the main power supply.

Often there are fuses on that board - one or more. Check those.

if they are blown you can try to replace them, but expect them to blow again - usually the whole board needs to be replaced.

often that *needs* to be done in a service center as there are some adjustments to be made after replacement.

Hope this will help in solving the problem....

I hate to say, but you have 1 or more shorted lamps in your panel. These lamps can be replaced, but is complicated and easy to damage other components. Your only other option is to buy another TV, because it would be cheaper that a replacement panel.

There are four screws located on the back of the tv twords the bottom. unscrew those then flip tv on its back to let the fallout. base should come free.

Not knowing the model right off but they are all basically the same it is on the on-screen menu.

The inverter board is probably bad. You can open it up and look for leaking caps or blown ic. You can probably find an inverter for that board on the net for about $60-90. If youre handy with a soldering iron, it'll be cheaper to repair. about $2-5 bucks for the capacitor and $10-20 for the IC.

Hello

With either the PC IN or HDMI connection, you can watch

your computer's display on the TV and hear the sound from the
TV's speakers.

When connecting a PC to the PC IN terminal on the TV, use an
analog RGB (15-pin) computer cable and a PC audio cable.

To use a PC, set the monitor output resolution on the PC

before connecting it to the TV. The following signals can be
displayed:

Format Resolution V. Frequency

VGA 640 × 480 60Hz

SVGA 800 × 600 60Hz
XGA 1024 × 768 60Hz

Other formats or non-standard signals will not be displayed

correctly.

Note:

• The PC audio input terminals on the TV are shared with the
HDMI-1 analog audio input terminals
• Some PC models cannot be connected to this TV.
OK.

toshiba will sell you a new one at about 800 dollars (worked at best buy and tha was the price for a 42 in screen) the best bet is to either take it to a local tv repair shop or buy a new tv at that price. new egg and tigerdirect.com have that model for about 800 dollars alone

i want full screen on my tv

Hi kelner1950,

This is an indication of out-of-regulation in the power supply section. The very common caused of this fault is the dried-up/leaky electrolytic capacitor in that section. It will drop the supply from normal voltage and will disable the unit and blinking error appear. Sometimes it has a bulged/dome at the top but not all, it is better that you have a capacitor checker/tester to determine its condition. Also, bad solder joints can produce the same symptom, it is hard to spot, you should use table lamp/portable lamp for finding the cold solder. Secondary reason of fault is the open fuse/fusible resistor in series with the output of regulator IC/transistor, shorted/openRegulator IC/transistor, shorted zener diode(all are in the power supply section) and the microcontroller. Best that you check the output voltage of each regulator to determine where the fault came from and narrow the job.

If you don't have necessary tools and test instruments, and can't do the job yourself, I would advice you to look for a professional to troubleshoot the problem. Don't attempt to work in the power supply if you don't know the safety precaution of handling it, there some stored electricity enough to hurt you with a little mistake only.

Also check if your unit is under warranty /extended warranty, avail it because the manufacturer of your unit will fix it for free. Don't open the back panel, this will void the warranty.

Hope I helped you.

Have a nice day!

Thanks for using Fixya.

its crt or lcd call me 919902889494

dear user,

dont use your lcd until its fault get fixed. lcd capacitor is leaking oil.kindly change the capacitor at your earliest

See page 5 of the owner manual:
Removing the Pedestal Stand
1) Carefully lay the front of the unit face down on a flat,
cushioned surface such as a quilt or blanket. Leave the stand
protruding over the edge of the surface.
Note: Extreme care should always be used when removing
the pedestal stand to avoid damage to the LCD panel.
2) Remove the jack pack cover on the back of the TV to expose
the pedestal stand screws. The jack pack cover can be removed
without tools.
3) Remove the five screws shown in the diagram below. This will
allow removal of the pedestal stand.
4) Once you have removed all five screws holding the pedestal
stand in place, remove the pedestal stand from the TV by
sliding the pedestal stand away from the TV.

http://www.tacp.toshiba.com/tacpassets-images/models/47HL167/docs/47HL167_om_e.pdf

http://www.fixya.com/support/r5093881-lcd_flat_panel_tv_troubleshooting_guide

http://s807.photobucket.com/home/budm/allalbums

http://en.wikipedia.org/wiki/Capacitor_plague

dear user,

may be hdmi settings is required.

on your lap top

Hello
I don't understand what your post is. Please clarify more about your tVs fault. If you haven't its user manual, send me a mail and get it back by return mail. It is an adobe acrobat reader document. Ok

Hello
Surely you can connect an external audio system to this tV. Connection should be taken from the TVs FIXED AUDIO OUT sockets at the back of your TV, with RCA cables,and can connect it to the respective sockets in the audio amp. OK.

The way it works is it slides up into the TV and bolts from the back, on the lower back

Remove 4x allen screws about 10cm from center at the rear of the television ps 4mm allen key required!