Top 20
Whirlpool RBS275PD Electric Single Oven - Page 2 Questions & Answers
BAKE & CLOCK BUTTONS DO NOT REGISTER WHEN PUSHED- CLEAN & BROIL BUTTONS ARE REGISTERING
If your oven is a touch pad model then the pads are bad. the touch pad assembly will need replacing. Sometimes you can remove the ribbon cable and reinsert it. It sometimes will make them work but not very often. Make sure the power is off first. Remove the control panel. You will see the ribbon cable. There will be small tabs on each side of the connector plug carefully unclip these and remove the cable and reinsert it. Be prepared to replace the panel.
11/25/2013 4:18:07 PM •
Whirlpool...
•
106 views • 0 helpful votes
Reset cooker
Turn off breaker for 5 minutes and then turn it back on.
11/20/2013 8:42:35 PM •
Whirlpool...
•
48 views • 0 helpful votes
How do i remove the oven door
Here is a step by step on door glass repair:1) open the oven door and look at the hinge on each side, there should be a moveable part sort of near the middle of the exposed part of the hinge. This is the hinge lock, or stop, whichever you prefer. 2) flip the hinge locks in place. 3) with the locks on place, try to close the door slowly. you'll notice that the door will push upward.4) when it does this, you can now lift the door and remove it from the rest of the machine5) To access the glass you going to have to take all the screws pretty much, making sure you remember where and how each one goes6) now the door should come apart and you have access to the glass****Note that there are a great number of makes, models, etc. This is a general instruction, and some extra steps may be needed **** If you need further help, I’m available over the phone at
https://www.6ya.com/expert/jason_4570d45317834dd3
5/28/2012 2:47:21 PM •
Whirlpool...
•
515 views • 1 helpful votes
Using self clean
This link will take you to the manual for your oven. You will find the self-clean instructions, starting on page 11:https://www.whirlpool.com/digitalassets/MLPDF/Use%20and%20Care%20Guide%20-%208300772.pdfNotice that the above is a .PDF file type. If you cannot view it after clicking on the above link, you need to install Adobe Reader onto your computer first. You can get the free download for it here:http://get.adobe.com/reader/Good luck--and please provide feedback if this helps!
12/17/2011 11:12:29 AM •
Whirlpool...
•
303 views • 0 helpful votes
EO F2 The oven will not start or stop. I can not
Hello Sonya,The E0-F2 error code means that the oven temperature was higher than it's supposed to be. Usually the oven overheats because of a defective oven temperature sensor and the sensor should be checked.
this is what the sensor looks like...it is located within the oven chamber(usually in the left side) to check it,it needs to unplugged and using a mulitmeter set to measure ohms,check the sensor to be between 1060-1100 ohms at room temp. if the sensor is way lower/higher that 1060-1100 at room temp the sensor is bad and needs to be replaced, if the sensor is within that range then the control board is the problem.GENE
11/3/2011 1:29:11 PM •
Whirlpool...
•
643 views • 0 helpful votes
Hi my whirpool oven is
Hello,
Usually the F-03 error code means you have a bad oven tempreture sensor. To test the tempreture sensor you would use a multimeter set to ohms. At room tempreture the sensor should read between 1000-1100 ohms any less then this and you would replace the oven tempreture sensor in the unit. If you have any further questions message me back. Please also remember when our chat has fully concluded to rank how this opinion has helped in your appliance situation it allows me to continue helping others in similar situations in the future. Thanks
Rick
p.s I also looked afterwards in your service manual and the F-03 error code does refer to the oven tempreture sensor
9/13/2011 7:59:02 AM •
Whirlpool...
•
1,018 views • 1 helpful votes
Not finding what you are looking for?