Top 20 Whirlpool RBS275PD Electric Single Oven - Page 3 Questions & Answers

I will se what i can do ,

Door is open but latch is locked.
If your latch switch or solenoid is shorted or open they need replacing
The reading on the solenoid should be around 175 ohms.
Service manual and more HERE If you need further help, reach me via phone at https://www.6ya.com/expert/dan_73bbd84fe1d95b61

sounds like the touch pad is bad from what you're discribing,i looked up your model on the sears site and it looks like the whole front panel comes all together,part number W10122300 and it's around 230.00 dollars.you can call your parts store and see if you can just get the touch pad and hopefully you can.i've seen this happen before,the start button is pushed alot of times and it can damage the touch pad by pressing it to hard or just from using it alot of times.http://www.repairclinic.com/PartDetail/Touchpad-and-Control-Panel/W10122300/1372156 copy and paste this,this is the repair clinic,if you buy a part from them and it doesn't fix your problem they will take it back no matter what part it is and i think it's free shipping.it's a good thing to know when the parts are so expensive,also here's the sears site so you can look up your machine.good luck with it.http://www.searspartsdirect.com/partsdirect/part-model/Whirlpool-Parts/Range-Parts/Model-YGY398LXPQ00/1198/0124160/W0703148/00002?blt=06&prst=0&shdMod=YGY398LXPQ00

Hello,

The F2 error code means that the over overheated by at least 100 degrees above the tempature that was set at the time. The usual reason the oven would over heat by so much is a defective oven tempature sensor and the sensor would need to be tested to see if is the problem to test the sensor it would need to disconnected from the wiring to it and measure the amount of ohms of resistiance AT ROOM TEMPATURE when the oven is off and cool. At room temp. the the meter used to check the sensor should display between 1060-1100 ohms,if the number is vastly different that 1060-1100 at room tempature the sensor is defiently bad and should be replaced. This is what the sensor looks like
it will be inside of the oven chamber and again to properly check it the wiring should be unplugged and the meter leads should be placed into the plug at the end of the sensor to measure the ohms


GENE

Open the oven door and you will see 4 screws around the edge, these hold the oven into the unit, remove the fuse from the power socket and with all the power off to your oven remove socket faciaand detach the power cable to the oven. Reconnect electrical socket facia and leave the fuse out. Please rate my helpfullness O

Hi

Error code F5-E0 indicates that there is an issue with the door latch switch assembly; if the switch tests open then the door lock assembly should be replaced. Hope this helps...please post back for further assistance.

Daniel

From Page 15 of the Manual:

Press and hold the "Custom Broil" pad for 5
seconds. A short tone will sound
NOTE: The temperature display will go off
and the temperatures displayed will
after a conversion. The temperature display
be converted. To switch back to "F, repeat the instructions above.
NOTE: The temperature display will go off after a conversion.The temperature display will reappear the next time you press a cook function command pad.

Good luck!

Hi

Error code F5 indicates that there is an issue with the door latch switch assembly; if the switch tests open then the door lock assembly should be replaced. Hope this helps...please post back for further assistance.

Daniel

Hello,

If your electric stove turns on but does not get hot, then it means there is a problem somewhere on the control unit of the stove. the most likely problem is the thermostat regulator. you need to check the thermostat regulator of the stove. once the thermostat regulator is bad it will turn on but will not get hot.

Check the thermostat of the oven.

Hope this was helpful, if you need further assistance, please do not hesitate to reach me here on fixya.

Goodluck,
Elect_Comp

Hello, Thank You for using FixYa. I will be helping you today.Sounds like the high limit thermostat failed,It is on the rear of the unit it is part number 9759243 Check the old one for continuity. This is a common issue with these units
Thank You and please rate my answer if it was helpful..

Hi,
If your electric oven is taking too long to heat or just not heating up right,then check out this tip that will give more detail about your problem.

Oven Problems Electric Oven is Heating Slowly or Poorly

heatman101

Hi

The part is not available anywhere, he is right, even if it was available it would have been around $300 which I think is not worth spending on this unit. Hope you understand, I am saying this as you can buy a new one instead. Hope this helps...please post back for further assistance.

Daniel

First, you need to check the 2 circuit breakers. One goes to the control board and the other one goes to the heating elements. If the heating elements still do not work, you would need to check them for continuity.
http://www.appliancepartspros.com/ http://forum.appliancepartspros.com/oven-repair-including-ranges-cooktops/

Hi,
If your electric oven is taking too long to heat or just not heating up right,then check out this tip that will give more detail about your problem.

Oven Problems Electric Oven is Heating Slowly or Poorly

heatman101

Hi,

If your electric oven is taking too long to heat or just not heating up right, then check out this tip that will give more detail about your problem.Oven Problems Electric Oven is Heating Slowly or Poorlyheatman101

Hello & Welcome to FixYa
Error code F5-E0 is a door latch failure and is displayed due to malfunction of door latch-switch assembly. First try to check the door latch switch, if fine then recommended repair is replacement of door latch-switch mechanism. Please get back to me if you have any other questions.
Kevin

Sometimes the only way to solve this problem is to contact me or another Whirlpool Technician. Reason being Whirlpool has taken a very strict course of action when people post Whirlpool manuals here or the public on-line. I also have 5 days a week that I can contact Whirlpool if the question is a hard to solve answer. This is rare. The problem you are having is related to possibly your door lock or thermal fuse and once self cleaning begins you are having a fault that turns the power off and can only be resolved by doing a series of diagnostics. Click here and this page will explain=> RBS275PD Electric Single Oven fault Resolution.jpg I will be happy to assist you (should it come to that) and others here at Fixya. Click=> Here and fill out the capsha. after I saw your post I pulled the service manual to see if there by chance was a one answer solution and it appears that you will need to follow the instructions if you request I will send. We all love those easy answers and this will be much easier one on one, Thank You and thanks for choosing Fixya, Sea Breeze
It could also be simple as a defective=> 9759243 Thermal Fuse



Parts Manual=> RBS275PD Owners Manual=> RBS275PD
Please rate this solution, Thanks, Sea Breeze

1.
If door latched:

1. Disconnect power from unit.
   
2. Check wires and connectors from control to door switch, then from door
   switch to control. If no damage to wires and all connectors okay, proceed to
   step C.
   
3. Replace door switch.
   
4. Re-apply power.
   
5. Press and hold any key down for 1 minute to clear F5 failure code from
   memory. F2 will appear. Press CANCEL and observe for 1 minute to ensure
   operation is correct.

2. If door not latched:

1. Disconnect power from unit.
   
2. Check wires and connectors from control to latch switch, then from latch
   switch to control. If no damage to wires and all connectors okay, proceed to
   step C.
   
3. Repeat steps A and B for door switch.

3. Measure door switch (door open = switch open small low voltage terminals).
Replace switch if defective.
4. Measure latch switch (unlatch = switch open,
CAUTION - oven light contacts are closed). Replace switch if defective.
5. If
corrections are made in any step, reconnect power to control. Press and hold any
key for 1 minute to clear R failure code from memory. F2 will appear. Press
CANCEL and observe for 1 minute to ensure operation is correct.
6. If failure
remains, disconnect power and replace control.

Note:
Applies to all F5-E... codes.
F5 - E1

Hello & Welcome to FixYa

This indicates an open/shorted oven temperature sensor and to solve this problem the sensor needs replacement. If you wan to be sure before replacing the sensor then you can test it with a voltmeter for around 1100ohms....if it reads more then this then it needs replacement however, if the reading is around or less then 1100ohms then it is the control board that needs replacement. Please get back to me if you have any other questions.

Kevin

Thermal fuse in the back of the oven (needs to be pulled out) needs to be replaced.
Oven repair in Santa Ana, CA
Appliance repair in Santa Ana, CA