Top 20 Whirlpool RBS275PD Electric Single Oven - Page 8 Questions & Answers

This means you have a bad temperature sensor.

This is a very simple part to replace so you will save a ton of money by replacing this part on your own.

There is a temp limiter on the back of the oven that could cause that problem.

If it is a fan assisted oven and the fan is still wiorking o/k, then you need to replace the oven element, located behind the rear panel in oven.
Please rate my solution.
Thanks.

The problem is probably caused by the oven thermostat that has gone out of range.
If it is out 40 degrees where ever you set it, then you can compensate by setting it 40 degrees lower, or alternatively, replace the thermostat.
Trust this helps you.

This could be either a problem with the keypad or the control. Here's the manufacturer's "recommended repair procedure":

1. Check keypad connector for firm connection.
2. Press CANCEL. If error code returns after 60 sec., replace keypad.
3. Replace control.

... not so good, they want you to replace the keypad and if that doesn't work replace the control board ... both very expensive!

First I suggest trying to clean up the keypad ribbon connection into the control board ... this is free! We put a procedure on our website that describes how to do it, heres the link:

http://www.fixyourboard.com/techzone/ovens/keypad_tail_clean/keypad_tail_clean.html

If you come to the conclusion that the failure is due to the control board, we can have a look at it for you if your comfortable to remove it. We repair oven controllers.

Or, if you want to send us the keypad and control board as a unit (they are bolted together) we can determine which is the problem and repair as needed.

Best Regards,
Bruce
www.fixyourboard.com

The E1- F5 error is a door lock error.

The control (TIMER) has likely failed in this instance - BUT...

Sometimes when you disconnect power to a range and reconnect it the electronic range control gets confused.
You should disconnect power again for 15 seconds and reconnect and see if that helps.

If it doesn't cure the E1- F5 error hold the bake button in until E0- F2 appears in the display.
This is the error for a stuck button on the keypad and is the way to clear the memory of the electronic range control.

Sometimes these work, but if the control has failed it won't make any difference.

Thanks for using FixYa - a 4 THUMBS rating is appreciated for answering your FREE question.(*UIHJ

F1-E1 - EEPROM Checksum Error - Disconnect power for at least 30 seconds and then reconnect.
Allow at least a minute after power has been restored and if error code reappears, replace control board (clock).


Thanks for using FixYa - a 4 THUMBS rating is appreciated for answering your FREE question
@@@@

The F3 E2 error code indicates that the electronic oven control board in the range senses an over-temperature condition in the oven.

This can be caused by a failed temperature sensor probe, a wiring problem between the sensor and the control board, or a failed electronic oven control board.
If the oven is apparently not overheating when this error code appears, then your likely failure is the temperature sensor probe.
If the oven is overheating, then you likely have a failed electronic oven control board due to a stuck relay not cycling the oven heating element off properly.


For replacement parts - head on over to PartSelect.com or RepairClinic.com and enter in your full model number for a full parts listing.
I recommend both sites because ...


FixYa has no affiliation with either site - I have been using and recommending them for years - trouble free.

PartSelect has a great schematic database for locating the part on your unit and great "testimonials" for each part that often times includes HOW-TO information.
RepairClinic has pictures of each part they sell and also a great how-to and troubleshooting for basic repairs.


If your unit has never been serviced - there should still be an original service manual enclosed in plastic taped to the inside of the shell.
In the service manual are Error codes, maintenance procedures, and troubleshooting steps you can follow.


Anything too complicated or beyond your scope should be handled by a professional.

If you think you want to tackle the repair - and have gotten stuck on a step - reply to your question and I will be glad to help you out.




Thanks for using FixYa - a 4 THUMBS rating is appreciated for answering your FREE question%$$#$RW

you cannot it is sealed.

If it is a drop down door with rear hinges, then you need to replace both hinges.
Please rate my solution.
Thanks.

it is normal for it to stay on until the glass gets below 110 degrees it is for safety reason

Probably the Thermal Overload Sensor burned out from the excessive heat during the cleaning cycle. It Is located on back side of oven.

no i do not think your elements are bad.it soundsd more like the main control board has malfunctioned.

It seems that your oven is dead. Smoke came out of
your oven signifies that the heater plate got damage. However, you may have it checked, before buying one.

check power going to the tstat.

Hi,

Seems like you found out the hard way what I wrote about in this tip...

Check it out it also contains some thing to try on how to unlock that oven..

Self Cleaning Oven Problem

heatman101

Asker's Testimonial " Wish I had read this first. I never would have usedthe self cleaning option. Thanks for the info!! " - amymrocks

There is an element that circles the rear fan, this is the common element and the most powerful.
Once you have the lid off, it's quick to test continuity on all elements.
Hope this helps
john

F2-E0 - Shorted Touch Pad (Keypad) - Check the connection between the touch pad (keypad) and control board (clock) to make sure it is secure.
Select the 'cancel' function and wait 60 seconds.
If error code reappears then replace the touch pad, or touch pad and control board (clock) if all one assembly.

Thanks for using FixYa - a 4 THUMBS rating is appreciated for answering your FREE question!#!#

HI, this is a sensor issue. You will need to check the oven sensor wires that link the actual sensor to the main control board. Make sure that the contacts are connected properly, and not loose, or corroded. If all the wiring checks out, test the sensor for the correct resistance readings.(you will need a multimeter for this test)

The most common oven sensor should be approximately, 1100 ohms when at room temperature. The others may be close to as follows:

100°F - 1143 ohms
200°F - 1350 ohms
300°F - 1553 ohms
350°F - 1654 ohms
400°F - 1753 ohms
500°F - 1949 ohms

If the sensor test is adequate, and the wiring is Ok at the control, this will lead to a failed control board. replace the control in this case.

There is a thermal relay on the rear of the oven that tends to blow during self clean cycles. It is the most likely problem.
Remove the oven,turn off the power,remove the rear panel to access the thermal relay.It is not re-settable. It must be replaced.