Top 20 Whirlpool RBS275PD Electric Single Oven - Page 9 Questions & Answers


There is a thermal relay on the rear of the oven that tends to blow during self clean cycles. It is the most likely problem.
Remove the oven,turn off the power,remove the rear panel to access the thermal relay.It is not re-settable. It must be replaced.

Whirlpool... | 81 views | 0 helpful votes


element

Whirlpool... | 945 views | 1 helpful votes


you have a bad clock board a stuck relay on the board.
get a new clock board.

Whirlpool... | 143 views | 1 helpful votes


Had same problem with my KitchenAid. 10 years old. Ran self cleaning cycle, oven died!!!! Called repair. Appears to be thermal fuse. Part on order. Microcomputer had some brown spots on it. Tey wanted us to replace it too. But will wait to see if fuse is problem. Repair - $150 vs. $570. If it's the higher price, we'll buy a new oven before putting that kind of money into it. Will NEVER run a clean cycle again even if I have to buy a new oven.

Whirlpool... | 549 views | 2 helpful votes


change temp control

Whirlpool... | 215 views | 0 helpful votes


Usually this is caused by either a bad temperature sensor, a shorted wiring harness, or commonly a faulty controller. The temperature sensor and wiring can be checked with an ohm meter.

When you program the oven for a high temperature what does the display read after ten minutes or so?

- www.fixyourboard.com

Whirlpool... | 309 views | 0 helpful votes


element,make sure clock is set though

Whirlpool... | 615 views | 0 helpful votes


The problem lies in your magnatone used for heating up the oven.You need a replacement for that.

Whirlpool... | 728 views | 1 helpful votes


most likely the safety latch got stuck from the super heat of the oven while cleaning. try tapping the latch with a screwdriver and hammer, spray a bit of wd-40 on it wont hurt. i believe the self cleaning on ovens is crazy, as the heat damages things, including the finish of the unit.

Whirlpool... | 275 views | 2 helpful votes


broiler comes on to create even heating through out the oven, sounds normal

Whirlpool... | 126 views | 0 helpful votes


Things to check- The screw in fuses, they are usually the 30 amp fuses for the oven. Next is the clock assembly, often these clocks will have the words "push for manual" or "turn for manual", this will put the clock back into the normal operating mode rather than the automatic mode. Next, you may have to remove the power and check for any burnt wires. If all checks ok, you will have to test the selector switch and oven control.
 Oven temp problems: Temperature is too low possible trouble makers, blown oven fuse, bake element is out, burnt wire, oven probe clips, oven temp control, oven temp sensor.
Temperature is too high in the oven possible trouble makers, oven temp control, oven relay ( if used ), oven probe clips, oven temp sensor, shorted wire.
These oven probe clips often rust off and the oven temp probe hangs down, or touches the oven wall giving false temperature readings to the oven control.

Whirlpool... | 2,281 views | 0 helpful votes


Adjusting circuit board settings for oven size.

Whirlpool... | 699 views | 0 helpful votes


The answer is not as hard as it seems. I just tried for 10 minutes unsuccessfully to put the glass back in the two side tracks. Well the glass actually goes in front of them, the top holds the glass in place.

Whirlpool... | 1,102 views | 4 helpful votes


This could be caused by the eye control switch,the eye itself is bad,or the electrical block where the eye itself plugs in.These can be checked with a volt/ohm meter.Also a wire could have burnt under the stove top.Hope this helps. Gregg

Whirlpool... | 166 views | 1 helpful votes


HI. this F-2 is a code that represents a oven temp that is way to high and it is not registering on the oven temp.

1. Look for welded relay contacts on bake or broil relays. If this happens, replace oven control (also called clock or ERC).
2. For SELF CLEAN models: check door lock operation.
3. Look for a high resistance connection or any other cause of high resistance in the oven temperature sensor circuit. Check sensor, sensor harness and sensor harness connection at sensor and oven control. Replace sensor if found defective.

Remember: Oven control (ERC) measures resistance of sensor circuit, not actual oven temperature.

Whirlpool... | 183 views | 2 helpful votes


the control panel, has a relay that controls the heating in the oven, it's not closing ther circuit. the electronic timer/control panel, has to be replaced

Whirlpool... | 241 views | 1 helpful votes


oven requires a separate, properly grounded four- wire 240 volt, 30 amp service with its own circuit breaker

Whirlpool... | 159 views | 0 helpful votes


Check the overload thermostat inside the back panel of the oven.
No continuity? Replace it.

Whirlpool... | 606 views | 0 helpful votes


You are probably going to find the lower heating element has failed. Your symptoms describe that failure exactly.

Reply back if you want instruction as to how to repair.

Whirlpool... | 548 views | 0 helpful votes

Not finding what you are looking for?
Whirlpool RBS275PD Electric Single Oven Logo

380 questions posted

Ask a Question

Usually answered in minutes!

Top Whirlpool Ovens Experts

John Tripp
John Tripp

Level 3 Expert

4656 Answers

Cindy Wells

Level 3 Expert

6063 Answers

Marvin
Marvin

Level 3 Expert

85219 Answers

Are you a Whirlpool Oven Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

View Most Popular

Whirlpool Ovens

  • Whirlpool Ovens

Most Popular Question

code f1e2 whirlpool electric range mean

  • Ovens
Loading...