AEG Favorit 50500 Built-in Dishwasher - Answered Questions & Fixed issues

u just try to delete

This seems like the anti flood system (polystireen float / micro switch) at the base of the washer is triggered,\. This puts the washer in pump out mode and stops inlet of water via the inlet solinoid. Dry the water on the base and then check for any water leaks. (pipe leak

I suffer the same issue it was only fixed by upgrading the washing tablets used

sounds like the heating element has gone out

Hi

The polystyrene float you are referring is the water inlet valve where water hose is connected to. You would need to check & replace the water inlet valve. Hope this helps... Please post back if you need more information.
Daniel

First make sure that the float valve is not stuck up with some thing under it, Its the little plastic cap at the left front bottom of dishwasher and should move freely by hand up and down and you should hear a slight click.

Hi,
Here is a tip that will help you to find out why water will not come into thedishwasher...

Dishwasher Trouble No Water entering Dishwasher

heatman101

Empty all the water from the salt resevoir, (I used a turkey baster), then rock the machine backwards and forwards a few times and empty the last few drops from the resevoir again.

Pull old seal out and push new seal in

could be due to goalpost seal in poor condition or door latch needs adjusting

Question edited for clarity. It is likely to be a control board issue. They are expensive, so call for diagnostics and service. The reason the dishes aren't clean is because it is stuck on wash, so there is no draining and rinses. This machine has some history! https://www.google.com/search?q=aeg+f34300vi0+dishwasher+keeps+running ..

If your AEG FAVORIT 35085 Vi dishwasher beeps five times and stops halfway through a wash cycle, there could be a few potential causes for this issue. One possibility is that there is a problem with the water supply, such as a clogged or partially blocked inlet valve. Another potential issue could be related to the drainage system, such as a clogged filter or a malfunctioning drain pump. It's also worth checking if the dishwasher's spray arms are spinning freely and not obstructed by any debris. If the problem persists, it is recommended to consult the dishwasher's manual or contact AEG's customer support for further assistance. They can provide specific troubleshooting steps and guidance based on your dishwasher's model and any error codes that may be displayed.

If the anti-flood device has activated on your AEG dishwasher, it means that water has leaked into the base of the dishwasher and triggered the safety device. The anti-flood device is designed to prevent water damage to your home and shut off the water supply to the dishwasher. To resolve this issue, you will need to locate the source of the leak and fix it. Here are the steps you can take:

1. Turn off the dishwasher and unplug it from the power outlet.
2. Disconnect the dishwasher from the water supply and move it away from the wall.
3. Check the inlet hose, outlet hose, and drainage hose for any cracks, damage, or loose connections. Tighten any loose connections and replace any damaged hoses.
4. Check the dishwasher door and gasket for any damage or debris that may prevent it from closing properly.
5. Check the dishwasher's interior for any leaks, such as a cracked spray arm or a damaged pump.
6. Once you have fixed the leak, you can reset the anti-flood device by tilting the dishwasher to one side to allow the water to drain out of the base. Then, level the dishwasher and plug it back in.

If you are unable to identify or fix the leak, it is recommended to call a professional technician for assistance.

no info generic answer inlet valve failure --short in valve circuit

Did you check the emergency shut off switch? Almost all under the counter dishwashers have a wall switch to interrupt the power. The problem is it can be shut of on accident.

Look at the screen on the drain.if its clear then check your drain for leaks
As it could be building pressure on the system..by not draining proper.

If you are reading this, then you probably own an AEG dishwasher with a ceiling arm. This part is important for the dishwasher to function properly and needs to be cleaned regularly. However, if it becomes loose or falls off, it can be a real headache to try and reattach it. In this article, we will walk you through the process of how to fix a ceiling arm back onto your dishwasher.

I would check for any bends in anything... a crimp of a wire or bend of a hose can mean the washer will not complete setup and will just refuse like a stubborn mule. If you find no bends or crimps in wires... the brain may be dead. It will be one solid motherboard and should be fairly easy to replace.

Question edited for clarity. Question moved from Washing Machines category. That sounds like a partially broken wire or a control board issue. You need a service call.