Top 20 AEG 24 in. Favorit 60870M Free-standing Dishwasher Questions & Answers

Could be: faulty power board (completly or only relay for heating element), faulty wiring between heating element and power board, faulty heating element (interruption, short circuit or current leakage,on some heaters faulty thermal protection). Depending on the model, the display shows the i60 fault code or the LED end of the program will flash 6 times (only model without display). Dado

Error "i30" means that water remains in base because leakage or overflow. In this case, in order to prevent flooding, drain pump running continuously. When we talk about AEG dishwasher, drain pump works even the power is turned off (must be connected to the wall outlet, otherwise anti-flooding system will not work). Remedy: you should first remove the water from the bottom of the dishwasher and determine leakage. If you work around the dishwasher, you always take care that appliance must be disconnected from the power supply. Dado

The most common cause of a fault "i10" is closed valve on the water supply line. So this failure indicates a problem with filling of water. Possible error causes: Closed water tap, Inlet valve faulty, inlet hose bent, softener system clogged, pressure switch or pressure switch hose obstructed or leaking, wiring from pressure switch to printed circuit board (PCB), wiring from inlet valve to PCB and finally PCB. Dado

Problem with inlet water. Could be: water tap closed, pressure switch....etc Dado

Matthew, in most cases when a circuit board repeats the same action over and over, there was a short and loss of communication with associated controllers. Obviously you have power to the control unit, so that means the instructions from the controller to the solenoids is lacking. You are correct in assuming the board needs replacement, however you must determine is the cost for replacement is worth the time and effort. An old machine means one repair after the other. If its relatively new; then it may be worth it.

If the END or DRYING indicator on the programme progress display is flashing, you can probably rectify the fault yourself. After rectifying an END or DRYING fault, press the button for the wash programme that has been started. The wash programme continues. If the fault is displayed again, than check water leakage in the battom of dishwasher. Malfunction: END and DRYING on the programme progress display are flashing simultaneously. Possible causes: The leak prevention system has been triggered. Remedy: Try to find and repair water leakage otherwise close the tap and call customer service. Dado

I think it is best to connect power cable directly to the interference filter where is normally connected. The interference filter is connected in the terminal board parallel to the mains feed. See below pictures: Dado

i have lost my manual can u tell me wat the 3 symbols mean please

Hello there and thank you for choosing fixya
This is a very common problem with these units
The problem is that the cycle timer goes wacky on these machines fairly easy this can be due to the water not being hot enough entering the machine 140-160 f. if it is not at that temp the machine will
not wash like it should also these timers will just simply fail so i would first check the water pressure and temp and ensure it is good then check all of the filters and then i would contact you local appliance dealer and see if they can test the timer for you this is normally tested for continuity to see if it is bad ok if it is replace it further more if too much detergent is used it will clog up the system and this can give a bad result too so ensure there is not detergent clogging it up any where ok
Hope this helps you out
Best regards Mike

i would need a full model number to assist you further which is normally located on the side of the door perimeter or door landing perimeter when the door is opened..Email to: [email protected] thank you .......... daniel

It is probably not oil. Its from a rubber gasket that is slowly dissolving inside. It has to be replaced before the machine will have a leakage. I´ve had the same problem myself. Using high-quality detergent, (usually tablets) that is less aggressive to rubber will extend the lifespan of the gasket in the future.

its probably anti flood error and u might have a small leak somwhere

Hi,
Check your heating element..

Dishwasher Problems The Heating Element not Working
http://www.fixya.com/support/r4589033-dishwasher_problems_heating_element_not

Dishwasher Maintenance
http://www.fixya.com/support/r4319937-dishwasher_maintenance

heatman101

Sounds like the Anti-Flood system activated (polystireen float at base of machiene coupled to a micro switch) the purpose of this system is to put the drain pump on and stops any other function on the machiene. The anti lood system activates when any amount of water appears on the bottom (caused by leaky pipe / blokked pipes / spills etc.) . Dry the water and rectify the leak. This should solve the problem.

I don't have the answer - but mine has been doing this too. There's now a metalic/electical smell that has me worried so I've resorted to a basin of water and fairy liquid! Did you solve your problem?

i fixed the problem by tipping the machine over slightly, as suggested by other members, about a pint of water came out the bottom and it now seems to work perfectly.

most fault codes are 10, 20,30.........90 not familar with c2. ther is a fault earky on in a prog where if the pressure switch does not retun to empty the prog stops and displays 10 or 30. the pipe leading from the front of the sump to the pressure switch can sag. tieing it up to stop the sag can cure this..

try checking that your salt container lid is on properly

Question edited for clarity. It is likely to be a control board issue. They are expensive, so call for diagnostics and service. The reason the dishes aren't clean is because it is stuck on wash, so there is no draining and rinses. This machine has some history! https://www.google.com/search?q=aeg+f34300vi0+dishwasher+keeps+running ..

If your AEG FAVORIT 35085 Vi dishwasher beeps five times and stops halfway through a wash cycle, there could be a few potential causes for this issue. One possibility is that there is a problem with the water supply, such as a clogged or partially blocked inlet valve. Another potential issue could be related to the drainage system, such as a clogged filter or a malfunctioning drain pump. It's also worth checking if the dishwasher's spray arms are spinning freely and not obstructed by any debris. If the problem persists, it is recommended to consult the dishwasher's manual or contact AEG's customer support for further assistance. They can provide specific troubleshooting steps and guidance based on your dishwasher's model and any error codes that may be displayed.