Seat belt stuck on '01 Ford Taurus, would like to know how to take it apart.

diagram of belt--- 02 is or should be the same as 01, here is how to replace belt! rotate belt tensioner to remove belt.---

Any seat belt that is stuck and will not release should be replaced not repaired. Hope this helps.

they are gravity fed from forward movement upon stopping so no it can not be removed for they are a seal unit which can not be taken apart. If taken apart they will not go back together for the casing is a pressed fit

this is a simple repair many dont know. remove or pull off plastic pillar post cover, seatbelt probably twisted inside. twist it back around so it runs flat and lube slightly with a light lube spray on metal gearing. i had the same problem w mine pk

use a 15mm box wrench on the nut retaining the tensioner pulley to pry the tensioner 'arm' against the spring to release belt. note belt routing on decal under hood,or make a sketch,to aid in replacement.
on OHV engine rotate clockwise
on OHC rotate counter clockwise
be sure belt is completely seated on pulleys

Hi mate.

If the seat belt is faulty in any way then replace it as a matter of safety.

Ray

please don't forget to rate, thx.

Retractor and Tongue—Sedan
SPECIAL SERVICE TOOL(S) REQUIRED Description Tool Number Safety Belt Bolt Bit T77L-2100A
NOTE: Safety Belt Bolt Bit T77L-2100-A should be used for safety belt removal and installation.

Removal

1. Remove rear seat cushion. Refer to Section 01-10 .
   

Seat Cushion, Rear Sedan
Removal

1. Apply knee pressure to lower front portion of the rear seat cushion. Push rearward to disengage rear seat cushion pad and frame (600A88) from rear seat cushion front retainers (63370).
   

1. Remove rear seat cushion from vehicle.
   

1. Remove rear seat back. Refer to Section 01-10 .
   

Seat Back, Rear 60/40 Split Bench—Sedan
Removal

1. NOTE: Safety belt bolts do not secure seat back to vehicle.
   
   Remove rear seat cushion as described.
   

1. Fold down back seat and remove two bolts in the center of each seat back striker plates.
   

1. Remove two bolts from outboard rear seat back frame retaining brackets.
   

1. Lift seat back up and pull forward to remove from vehicle.
   

1. Remove panel (52018) and quarter trim panel (31012). Refer to Section 01-05 .
   

Trim Panel, Quarter—Sedan Removal

1. Remove rear seat. Refer to Section 01-10 .
   

1. Pull up on rear section of rear door scuff plate that overlaps lower quarter trim panel.
   

1. Pull lower quarter trim panel away from body.
   

1. Remove safety belt retaining bolt.
   

1. Feed safety belt through lower quarter trim panel.
   

1. Remove safety belt anchor plate-to-sill bolt from quarter panel.
   

1. Remove retractor anchor nut and retractor from rear quarter panel.
   

1. Remove upper seat belt anchor bolt and anchor from upper rear quarter panel.
   

1. Slide anchor plate end of safety belt through the openings in the quarter trim panel.
   

1. Remove outboard front safety belt retractor and tongue (611B08) from the vehicle.
   
   
   
   
   
   Item Part Number Description 1 386277-S190 Bolt (Part of 611B68) 2 31012 Upper Rear Quarter Trim Panel 3 611B60 Retractor and Tongue 4 N800937-S190 Nut 5 389370-S190 Bolt 6 — Rear Quarter Panel (Part of Body) 7 52018 Lower Rear Quarter Trim Panel 8 — Mounting Stud (Part of Body)

1. Remove seat belt anchor bolt and retractor and tongue from rear deck panel.
   
   
   
   
   

Installation

1. To install, reverse Removal procedure.
   

1. Make sure the safety belt webbing is not twisted. If it is, remove the twist.
   

1. Tighten retractor anchor bolt and safety belt anchor plate-to-sill bolt to 34-46 Nm (25-33 lb-ft).
   

1. Check the restraint system for proper operation.
   

you may have to remove the bolt that holds the buckle to the floor. Try to push the belt into the retractor and see if it frees up.

I assume you are saying it is in the locked mode. It has an automatic lock mode for holding a child seat. When the belt is pulled all the way out, it goes into locking mode. You will hear it ratchet when the belt starts going back in.



Section 01-20A: Restraints, Active 1999 Taurus, Sable Workshop Manual
DESCRIPTION AND OPERATION Safety Belt, Lap/Shoulder The dual locking mode retractor on the shoulder belt portion of the combination lap/shoulder safety belt for the front seat passenger and rear seat outboard passengers operates in two ways:

1. In the vehicle sensitive (emergency locking) mode, the shoulder belt retractor will allow the occupant freedom of movement, locking tight only on hard braking, hard cornering or impacts of approximately 8 km/h (5 mph) or more. The front and rear outboard seat belt retractors can also be made to lock by pulling/jerking on the belt.
   

1. In the automatic locking mode, the shoulder belt retractor will be automatically locked and remain locked when the combination lap/shoulder safety belt is buckled and does not allow the occupant freedom of movement. This mode provides tight lap/shoulder belt fit on the occupant and on a child safety seat or infant carrier installation restraint.
   

1. When the combination lap/shoulder belt is unbuckled and allowed to retract completely, the retractor will switch to the vehicle sensitive (emergency) locking mode.
   

WARNING: REAR-FACING INFANT SEATS SHOULD NEVER BE PLACED IN THE FRONT SEATS.
The automatic locking mode must be used when installing a child safety seat on the front passenger seat and rear outboard seats where dual locking retractors are provided

the seat belt could possibly be a sensor in the seat and the other problem more likely is the drive belt itself

Hi, ON your 2002 ford taurus, The Flashing code 33 ( B 2292 )

This code refer to : Driver side seat belt pretentioner ( seat belt bucklet) problem.

Check the conecctions under the driver seat.
Repair as need, and recheck if thi code is present.

But if you had an accident on you taurus. You need to replace the Seat belt Pretentioner ( seat belt bucklet)

OK. I hope this information work for you.

Than's.