20 Most Recent 1998 Ford Mustang Questions & Answers


I would try looking on ebay. You can purchase inexpensive parts on there. Mike. Rate 100% please.

1998 Ford... | Answered on Oct 07, 2019


In the IP fuse panel #6 fuse is a 15A and #17 fuse is a 30A.

1998 Ford... | Answered on Apr 03, 2019


Check your battery to make sure it has enough power and cranking amps to turn that starter and flywheel.  Make sure that your cables are good and move them around to see if that helps. Sometimes those cables can break and corrode inside the outer covering and you can't see it which makes it hard to diagnose. Clean your battery posts and cables. Also another thing you can try is starting in neutral or rolling your car back a few feet to allow it release some tension and hopefully free up allowing it to crank over easier. When you replaced the starter did you make sure to slide it in place and tighten it down good? Did you use shims to allow proper clearance room?...

1998 Ford... | Answered on Sep 20, 2018


There isn't any. The EDF relay is in the CCRM which is in the engine compartment. If the CCRM isn't obvious, trace the BLK/ORG wire from the engine compartment fuse box and the RED/ORG wire from the electric cooling fan motor.

1998 Ford... | Answered on May 13, 2018


Your readiness test will allow your PC to reset & if u are going to get a check engine light that's going to come that's the time it will come on, after the "readiness road test" Take it out & dive high & low speeds. If that light is to come on it will.

1998 Ford... | Answered on Mar 15, 2018


In my opinion they definitely should have checked them the first time. Some freezer plugs aren't that difficult to change. I have also seen people just slap some high temp sealant on them to repair the holes. More commonly they just rust out and they probably should have seen that when they were looking for licks the first time.

1998 Ford... | Answered on Feb 19, 2018


Have you replaced the broken hose? The bad part can cause the other codes to appear so fix what you know is bad, disconnect the negative battery cable for 10 minutes afterwards and then start it up and see what happens.

All you need to do with the codes are to put each one in the search bar and search for ford code p1443, ford code p0136, and ford code p0141. But do that after you fix the obvious problem.

1998 Ford... | Answered on Feb 19, 2018


I suspect the fuel injection is poor. Try to check the fuel pump, there maybe no much pressure from the pump.

1998 Ford... | Answered on Feb 04, 2018


Depending the style. Go to google. type in 1998 ford mustang fuse box diagram and search for images.
Locate the closest one to your fuse box and look on label for "fan"

I’m happy to help further over the phone at https://www.6ya.com/expert/zelio_00a80ed57645ccbf

1998 Ford... | Answered on Jan 16, 2018


Oxygen sensors may be reading false rich making it go too lean .

1998 Ford... | Answered on Dec 31, 2017


If the antitheft light is blinking then the pcm is not getting a signal from the PATS transponder. The Check transponder ring, wiring, PCM fuse in under the hood fuse panel, and lastly pcm. Good luck.

1998 Ford... | Answered on Nov 23, 2017


Check your Constant Control Relay Module.

1998 Ford... | Answered on Nov 23, 2017


P0305 is a # 5 cylinder misfire , do you know what that is ? Check engine light flashing indicates a severe misfire that can damage the catalytic converter . Don't drive this vehicle ,take it immediately to a qualified repair shop or the dealer .
A Ford P0171 is a LEAN code for cylinder bank 1, and P0174 is a LEAN code for cylinder bank 2. These codes commonly occur on many Ford vehicles, and are set when the powertrain control module (PCM) sees the air/fuel mixture is running too lean (too much air, not enough fuel).

Flashing check engine light CarMD

1998 Ford... | Answered on Oct 24, 2017


Hi, Needs a new fuel pump sorry to tell you. Please leave me feed back: Malcolm Campbell, Thanks.

1998 Ford... | Answered on Oct 24, 2017


Most alarms have a set way to reset go to dealer site on line and look for alarm reset for that car . Some set by cycling key three times, some have a reset code for door pad. Best of luck finding it.

1998 Ford... | Answered on Oct 08, 2017


The system at this point is shot. The dryer is contaminated with oil and will not function correctly even if the leak were sealed. The system will have to be evacuated , flushed and leak tested, repaired and recharged.

1998 Ford... | Answered on Oct 04, 2017

Not finding what you are looking for?
1998 Ford Mustang Logo

999 questions posted

Ask a Question

Usually answered in minutes!

Popular Products

2000 Ford Mustang
2000 Ford Mustang

668 Questions

2001 Ford Mustang
2001 Ford Mustang

632 Questions

2002 Ford Mustang
2002 Ford Mustang

587 Questions

1995 Ford Mustang
1995 Ford Mustang

575 Questions

1996 Ford Mustang
1996 Ford Mustang

418 Questions

Top Ford Experts

Marvin
Marvin

Level 3 Expert

85216 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22485 Answers

gerry bissi

Level 3 Expert

4388 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

View Most Popular

Mustang Ford

  • Mustang Ford

Most Popular Question

998 ford mustang 3 8 ccrm relay

  • Cars & Trucks
Loading...