Question about 2000 Chrysler Sebring

1 Answer

I have a 2000 Chrysler Sebring. The check engine light is on. The reading is misfire on cylinder 1. Is there a diagram that shows the cylinder by #?

Posted by on


1 Answer

  • Level 1:

    An expert who has achieved level 1.

    New Friend:

    An expert that has 1 follower.


    An expert that hasĀ over 10 points.


    An expert whose answer gotĀ voted for 2 times.

  • Contributor
  • 10 Answers

This is a common issue with stale gasoline. Run some injector cleaner and have your mechanic reset the light.

Posted on Sep 04, 2010


1 Suggested Answer



Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017


Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

P0303 cylinder 3 misfire in 2008 Chrysler sebring convertible, changed all spark plugs & coil pack. Engine light continues to come on with this code ?

Recheck all work you have done. Sometimes folks replace the wrong coil pack as they can be easily confusing. If everything seems ok, there are still two possibilities. First, ensure that the fuel injector is consistently firing for the cylinder, and also ensure that it is not constantly firing. Either can cause a misfire, one for too little fuel, one for too much fuel. Lastly, check compression in the suspect cylinder. A broken or burnt valve can cause loss of compression, leading to misfires.

Aug 10, 2016 | 2008 Chrysler Sebring Convertible

2 Answers

2009 chrysler sebring changed spark plugs cause it said number 3 was misfireing them put in a new thermostat in it started up but then started back not wanting to crank it acts like its flooding

were you sure to set the gap on the plugs? and replace them with the correct plug for that matter? also...why was the thermostat replaced?

Sep 10, 2015 | Chrysler Cars & Trucks

1 Answer

Random misfire/distributor problems

IF you have a seperate coil (1 coil only) check for correct voltage for the coil as most start on 12 volts and run on 7 volts and have a resistor in the circuit. Randomj misfire may be the coil breaking down as it gets too hot from the incorrect voltage

Feb 23, 2013 | 2002 Chrysler Sebring

1 Answer

What cylinder is #1 on a chrysler sebring 2.7 l V6

Here is a link to give you all Chrysler Firing Orders, it also shows you ththe cylinder #'s :

Jul 17, 2012 | 2005 Chrysler Sebring Convertible

1 Answer

3rd cylinder is misfiring. how to fix?

For engine misfiring problem check the help links mentioned below. Click the link below to go through the troubleshooting procedure :---- Engine misses and truck jumps? Hard to down shift? Issue with high gear only?

Bad miss at idle?

While stop engine idles like cylinder missing?

Engine Misfire codes for car?
Engine Misfire codes?

Misfire on cylinder 4?

Oil on spark plugs and car misfires?


This will help.


Mar 07, 2012 | 2006 Chrysler Sebring

1 Answer

Had engine light on and running ruff. Had code checked at auto parts store and it shows misfire on clyinder 2. How do I locate cylinder number 2 on a 2004 Chrysler 6 cyl Pacifica

Most front wheel drive V6 chrysler engines are as follows: standing on passenger side of car facing engine, cylinders 1-3-5 are on the left bank, cylinders 2-4-6 on the right. Standing at the hood facing engine (front of car) #2 is on your left front corner of engine. Change / check plugs and wires before doing and deep sensor testing.

Jun 11, 2011 | Chrysler Pacifica Cars & Trucks

1 Answer

I have a 2000 chrysler concorde that the engine light just popped on - the error codes are po302, po420, po340

P0302-cylinder #2 misfire detected
P0420- catalyst efficiency below threshold bank 1
P0340-No cam signal at PCM.
The Cam sensor most likely needs to be replaced first. Clear the codes after that and drive and see what comes back on.

May 29, 2009 | 2000 Chrysler Concorde

2 Answers

Tried switching injectors reflashed PCM spark plugs but still p0301 comes back, car runs good

Code P0301 = Cylinder 1 Misfire Detected
Start with the “easy to check” items first...Some of these checks/repairs require specialized tools or equipment. A trusted repair shop or dealer would be would be advised to correct this problem.
Try changing the spark plugs, Check the coil, TPS sensor & MAP sensor voltage. Check the fuel pressure, check for vacuum leaks including intake manifold. Dirty or plugged injector, timing, compression test-including leak test--meaning, put #1 on TDC then charge the cylinder with air (~30lbs), and check for leak via exhaust/intake. Update PCM to the latest software, Worn camshaft.

May 19, 2009 | 2004 Chrysler Sebring

1 Answer

Random Misfire

yes disbuter buddie is bad nad its form oil getting in plugs form bad gaskets on valve covers ok so u need new disbuter then gaskets redone stop oil geting in ther i have one these i know it all on this car

Oct 07, 2008 | 2000 Chrysler Sebring

Not finding what you are looking for?
2000 Chrysler Sebring Logo

338 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chrysler Experts


Level 3 Expert

85223 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22485 Answers

Jonah Oneal

Level 3 Expert

14092 Answers

Are you a Chrysler Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides