20 Most Recent 2002 Chrysler Sebring Questions & Answers

On the console there should be a little door. If you open the door and use a narrow screwdriver in this hole it should allow you to take the car out of park. Be sure that you have your foot on the brake when you do this or the car may move.

Not much on that job. Usually when you buy a new headlight unit they come complete, you just bolt them in. https://www.google.com/search?q=2002+Chrysler+Sebring+headlight+adjustment+screws and https://www.google.com/search?q=2002+Chrysler+Sebring+replace+headlight+assembly ..

For full diagrams you need a repair manual, or there are sites that charge. This site says 'free'.Many sites will give free partial diagrams, so Googleyear make model (the part) wiring diagram.https://www.google.com/search?q=2002+chrysler+sebring+3.0+wiring+diagram..

Question edited to add maker. Question moved to category. You need a transmission specialist, or an auto-electrician with a pro grade scan tool. Modules, Sensors, and Solenoids.

What, you want someone to write a 5 page personal manual for you on how to do it? Do you not have Google in your neighborhood?

Fig. Intake manifold bolt torque sequence 2.7L engine

Upper intake manifold with a new gasket on the lower intake manifold and torque the bolts, in sequence, to: 105 inch lbs. (12 Nm)

Hope helps (remember to rate this answer). Good job.

If you're not hearing a click from the starter check for a starter relay. May be burned out! DO you hear the fuel pump kick in when you turn the key on? If not something might have triggered your security system and locked you out!

well you call or go into your local auto parts store and ask them to see one ,perhaps they will explain it to you on where it is and how to replace it .I am not a Chrysler fan

First, thoroughly clean all mating surfaces, then lubricate the cylinder head bolts' threads with engine oil. Next, follow these steps in sequence: 1. Bolts 1-8: 35 ft.-lbs. (48 Nm). 3. Bolts 1-8: 55 ft.-lbs. (75 Nm). 4. Bolts 1-8: 55 ft.-lbs. (75 Nm). 5. Without using a torque wrench, turn bolts 1-8 - An additional 90°. 6. Bolts 9-11: 21 ft.-lbs. (28 Nm).

Some vehicles have a sensor that lets i know the the trunk lid is open ie the deck. Thier should be some kind of switch that is actuated by the deck and it may be faulty or just need adjusted,

if you run out gas, you have probably damaged fuel pump. thr fuel in tank keeps the pump cool.

What doesn't work? It may not connect to anything. The harnesses are made for all accessories and you may not have that accessory like auto temp control or something like that, so if everything is working don't fix it. I hope this helps. Take care.

The schematic shows that you have a relay and a fuse located in the fusebox under the hood (as opposed to the fusebox that is located in the side of the drivers dash). The problem seems to be that the washer pump shares the relay with the headlamps and the fuse. If your washer pump isn't working but your headlamps are, your washer pump is probably shot and you need a trip to the autoparts store (probably $20 bucks and 30 minutes to fix). Here is a shot of what should be your under-hood fusebox:

There is a TSB for this issue: It is in "limp" mode. It is not unusual for the Sebring - Should be covered by Chrysler.

TSB Number: 0801505









NHTSA Number: 10013731

First two things to check-spark and fuel. Check fuel pressure with a fuel pressure gauge tester, check for spark on a plug wire. If no or too low fuel pressure (should be about 40-50psi, check specs for it) suspect bad fuel pump or clogged filter or pump wiring circuit problem. If no spark, diagnose the ignition system.

Check for a loose connection or corrosion at the battery and cables.

Clean your battery terminal and all ground connections. Get the battery tested. Replace if necessary. If it still happens, you'll have to get an electrical diagram and check circuits from the ignition switch to the starter

Check the drive axle and make sure that it didn't come apart inside the boot.